Software Changelog

ID:
Search for resolved Bug or Feature Request:

Version 4.4.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
4405SAMLight31.10.2025FeatureUNIX timecode
4354USC-3 Firmware29.10.2025BugfixLaser relevant changes can happen before laser gate is off if mark delay is lower than laser off delay
4372SAMLight29.10.2025FeatureAdd new Icon Pack for SAMLight Toolbars and Entity List
4320SAMLight16.10.2025FeatureAdd optional flag 'Lock Toolbar'
4361SAMLight16.10.2025FeatureAdd User Level which en-/disables Remote tab of global settings
4382SAMLight14.10.2025BugfixUser without "Load" Privilege should not be able to load files anyway
4368SAMLight01.10.2025BugfixWaveLength Factor overflow issues depending on RedPointer mode
4377SAMLight30.09.2025BugfixStarting the redpointer on sub-entities with "mark selected" active causes MIP and mark time issues
4343SAMLight30.09.2025FeatureAllow toolbar buttons to be replaced with png images
4350SAMLight30.09.2025FeatureAdd new feature Big Text
4376SAMLight30.09.2025FeatureAdd option for big icons in object list
4366SAMLight29.09.2025BugfixWrong wobble amplitude in multihead configurations with different field sizes
4319SAMLight18.09.2025BugfixUpper left toolbar does not redock to leftmost position
4285USC-3 Firmware09.09.2025BugfixFCI - TMB command translation parameter limited between -100-100 bit.
4346SAMLight08.09.2025FeatureAdd GCode Command SETMOFOFFSETREL using relative offsets
4314SAMLight02.09.2025BugfixNon-default horizontal alignment for dynamic barcodes with quiet zone in flash is wrong
4328SAMLight21.08.2025BugfixSimmer Value will not be stored
4312SAM13.08.2025BugfixUSC3 crashes if tilt compensation is enabled with a z offset of 0
4313SAMLight12.08.2025FeatureAdd a "USC Time" dialog to make it easier to set the USC date and time
4289SAMLight24.07.2025FeatureCCI constants to retreive analog in values
4297SAMLight24.07.2025BugfixStandBy half period limited to integer
4271SAMLight21.07.2025FeatureShow frequency in mark property page grid for all laser types
4274SAMLight01.07.2025BugfixMarkFlagMarkDialogWaitForTrigger not returning current state
4284SAMLight30.06.2025BugfixBackground Camera does not Allow Mirroring Axes
4277SAMLight24.06.2025BugfixCCI Command LongValueTypeDongleSystemNumber during marking produces undefined behavior
4260SAMLight23.05.2025BugfixExpected Mark Time not considering control objects
4248SAMLight06.05.2025FeatureExternal custom controller (Type 4) sleep time before some commands
4233SAMLight15.04.2025BugfixExport slice as .plt via CCI not working in SAM3D
4237SAMLight15.04.2025FeatureGet command for scComSAMLightClientCtrlLongDataIdQrCodeExVersion
4227SAMLight21.03.2025FeatureCustomizable CCI command to retrieve multiple values
4200SAMLight24.02.2025BugfixCheck to Working Area should not check non-markable entities
4190SAMLight19.02.2025FeatureUSC-3 defocus through lookup table
4192SAM06.02.2025BugfixImporting MCL files in 64 bit versions of the sam library does not work properly
4176Installer21.01.2025FeatureCreate Desktop Shortcut with the installer

Version 4.3.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
4020SAMLight11.08.2025FeatureAdd support for second laserport with dedicated power map
4162SAMLight25.03.2025BugfixHuman-Readable text of barcodes will not decode tilde mode if utf8 is enabled
4163SAMLight07.01.2025BugfixSTL projection successive line arrays can cause laser off/on
4151SAMLight18.12.2024FeatureAdd Dialog to Change All Text2D Objects Simultaneously
4129SAMLight11.12.2024FeatureAllow scaling of Bitmaps preserving current DPI ( dots per inch ).
4165SAMLight10.12.2024BugfixCCI-Command Various Text Parameters Does Not Affect Limit of Serial Numbers as Barcode
4155SAMLight09.12.2024BugfixInvalid wobble amplitude 2 values trigger error message even if unused
4158SAMLight09.12.2024BugfixDrill causes additional delay
4138SAMLight20.11.2024BugfixASCII CCI command can stop the marking process too early
4131SAMLight20.11.2024FeatureOption to hide menu bar and status bar in SAMLight
4094SAMLight20.11.2024FeatureAdd new Toolbar that can be filled with a String sent by Client Control
4148SAMLight20.11.2024Bugfix"Disable Stop via Mouse Click" does not work with TriggerMode
4141SAMLight20.11.2024BugfixDXF CCI import ignores import flag KeepOrder
4136SAMLight29.10.2024FeatureCCI command for YAG pen power2 value and enable flag
4121SAMLight28.10.2024BugfixError when Opening and Closing SAMLight several Times using RTC-6-Ethernet
4104SAMLight16.10.2024BugfixMultiHead in Combination with SAMLight JobIOSelect needs Inputs from all Cards to work correctly
4127SAMLight15.10.2024BugfixRTC no 8-bit LP output
4123SAMLight09.10.2024BugfixSlider for Pen Settings Speed value at wrong position.
4103SAMLight30.09.2024BugfixCreate Beam Comped Copy does not work for Inner and Outer Polylines simultaneously
4102SAMLight22.08.2024FeatureCCI command for copying hatch parameters from one entity to another
4086SAMLight08.08.2024BugfixSAM3D Slicing in negative z results in missing slices
3942SAM04.07.2024FeatureAdd support for RTC6 Ethernet
2381SAMLight14.06.2024BugfixCW mode message appear on pen settings page of IPG Laser
4064USC-2 Firmware13.06.2024BugfixZ overflow reset does not work.
4062USC-3 Firmware07.06.2024BugfixZ overflow reset does not work.
4042USC-2 Firmware07.06.2024FeatureRework Overflow Function
4052SAMLight06.06.2024FeatureAdd new lasertype for new IPG Laser with pulse picker option
4055SAMLight31.05.2024BugfixInclude Options to Press "Enter" Key instead of Go in Dimension Dialog
4036SAMLight13.05.2024FeatureCCI Splitlines should not be detected as objects
4001SAMLight26.04.2024FeatureRemove the limitation to +-fs/2 in the Z lookup table
4027SAMLight10.04.2024FeatureInclude Day Seconds as Format in DateTime Objects
4019SAMLight22.03.2024BugfixJobs with barcode reader mode can lead to crash in SAMLight JobIOselect mode
4003SAMLight14.02.2024BugfixSL Crash with Hatch of Parameter-Finder
3970USC-3 Firmware16.01.2024BugfixIncorrect handling of invalid FCI commands beginning with the letter "u"

Version 4.2.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
3834SAMLight15.10.2024FeatureSAM3D - option to manually specify borders (number, distance, pen)
3882USC-3 Firmware16.01.2024BugfixSupport multiple telnet connections
3966USC-3 Firmware16.01.2024FeatureFCI command to get USC type (USC-2, USC-3)
3961SAMLight08.12.2023BugfixPrinting the format string of a serial number in a flash job without a datetime element can crash
3943SAMLight20.11.2023Bugfixsc_corr_table without dongle corrupts sc_resource_settings.sam
3937SAM13.11.2023BugfixClicking the "Zoom" toolbar button twice keeps the mode active until disabled with another toolbar button
3938SAM13.11.2023BugfixSome old barcode types do not work in x64 version
3907SAMLight05.10.2023BugfixPowermap dialog cannot be closed if USC1 was externally stopped before
3931SAMLight29.09.2023FeatureQR Code Ex Add possibility to choose number of dots 1,4,9,16
3906SAMLight14.09.2023BugfixHPGL import with points can have issues if polylines are not closed
3908SAMLight01.09.2023BugfixFor B&W Bitmaps in bidirectional marking the lineshift by LaserOn and LaserOff delay is inverted
3905SAMLight30.08.2023BugfixIssues with external barcode types and long content in SAMLight x64
3887SAMLight29.08.2023FeatureCCI commands by index
3846SAM16.08.2023FeatureFont DropDown ComboBox on Text Property Page should be highligted in red if font is not availabe
3875SAMLight14.08.2023FeatureNew Import Filter SVG Scaps
3884SAMLight07.08.2023BugfixSet Defocus via CCI needs to be done twice for RTC6 to be executed
3866SAMLight19.07.2023BugfixDisable Mark and Redpointer Enable in Parameter Finder in case of DemoMode or Jobeditor
3877SAMLight17.07.2023BugfixNegative USC defocus is not working
3809SAMLight30.06.2023BugfixSAMLight crash if string commands contain percent signs and cci logging is active
3851SAMLight01.06.2023BugfixSVG import - curve is displayed as a straight line
3811SAM12.05.2023BugfixBackground entites are still selectable via rectangular selection
3776SAMLight12.05.2023FeatureSAM3D - option to specify mark order and disable contour splitting, individual contour loop definition
3843SAMLight08.05.2023BugfixSAMLight x64 freezes during the UNF generation of a dynamic barcode.
2705SAMLight24.04.2023Featureeach Hebrew letter is not recognized so that "Character based splitting" does not work in Hebrew
3815SAMLight04.04.2023FeatureNew CCI commands to enable dynamic grayscale map and set the points of the system pixel map
3825SAM24.03.2023Bugfixjump speed display in pen should respect optic gain values
3820SAMLight16.03.2023BugfixWithout width and height definition in root of SVG, the default unit for SVG should be mm
3814USC-2 Firmware13.03.2023BugfixMemory corruption if telnet commands exceed 2048 characters
3802SAMLight10.03.2023BugfixMultiHead and MOTF job saved with job properties "MOTF Multiplier" overwrites multiplier values of non-zero heads when loaded
3775SAM01.03.2023BugfixWrong power value applied during jump in gray advanced bitmap marking with activated jump over blank pixels
3710USC-3 Firmware01.03.2023BugfixRMOTF for Channel 1 does not work in Flash if rotation is set for a disabled Channel 0
3774SAMLight01.03.2023BugfixOptic Flags are not applied for Head1 in SAMLight for MultiHead
3569SAMLight01.03.2023FeatureAdd new 3D surface cone for Optic3D
3787SAM01.03.2023BugfixRTC6 in standard mode uses 20 bit instead of 16 bit for the defocus
3803SAM01.03.2023FeatureReduce job size with included pens
3795SAMLight01.03.2023Feature1D and 2D splitting does not work if bitmaps are marked in gray advanced mode (or usc2 with pen frequency)
3794SAMLight01.03.2023BugfixOverlap of Upskin and Downskin with one-layer thickness
3792SAM24.02.2023BugfixWrong point can be inserted in multihead split if start/end is exactly on split border
3777SAMLight16.02.2023BugfixUsing the test I/O in USC1 advanced settings deactivates all other currently set I/Os
3791SAMLight09.02.2023BugfixAll cameras are deactivated if one camera fails
3767SAMLight31.01.2023BugfixBitmap extended limits and position does not work

Version 4.1.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
3688SAMLight09.04.2025FeatureTry to activate scanahead again on output start if activated in software but not yet successfully activated on rtc/excelliscan
3582SAMLight02.03.2023BugfixSetOutput entity pulse length larger than 1000 is reset to 1 when re-selecting the entity
3585SAMLight02.03.2023FeatureAdd checkbox in hatch property page for mitered edges in SAMLight and SAM3D
3602SAMLight01.03.2023BugfixMark and jump delay are missing for perforation
3604SAM01.03.2023BugfixSkywriting in Flash for serial number entities is not correct if they are resized
3623SAMLight01.03.2023BugfixLong import times for large layer files
3575SAMLight01.03.2023BugfixWobble is not repeated when Repeat Mark is enabled.
3642USC-3 Firmware01.03.2023FeatureReport cause of marking failure in FCI LOG
3719SAM01.03.2023BugfixDXF Import LWPolyline has a different max error compared to regular Polyline
3641USC-3 Firmware01.03.2023BugfixUSC card crash if QR code has an overflow
3643SAMLight01.03.2023FeatureHorizontal alignment for barcodes (including Flash)
3709SAMLight01.03.2023BugfixCreate Screenshot via CCI is not influenced if entity is set to Hide in View2D
3726SAMLight01.03.2023BugfixOverlap area of Multihead system contour and hatch of an entity are assigned to different heads (using Datawizard)
3753SAMLight01.03.2023BugfixDate Time / Serial Number Entity can disapear in View2D with Mark Trigger and PartCounterMode
3578SAM01.03.2023FeatureAdd new EAN-13 barcode that supports negative line reduction
3639SAM27.02.2023BugfixView3d supports a maximum of 65536 objects
2962SAMLight16.02.2023FeatureImplementation of new IPG laser - UKP-Laser YLPP-25-3-50-R
3667SAMLight15.02.2023FeatureGenerate 3D correction file with sc_corr_table using z-lookup table
3741SAMLight31.01.2023FeatureMultiHead Execute control objects on all heads in MultiHead independent mode
3759SAMLight20.01.2023FeatureHide user level in SAMLight
3725SAMLight23.12.2022FeatureMultiHead A function to assign the entity in overlap area of working areas to a specific head
3769USC-2 Firmware20.12.2022FeatureMOTF reset should try to avoid overflows
3769USC-3 Firmware20.12.2022FeatureMOTF reset should try to avoid overflows
3707SAMLight09.12.2022FeatureAdd priority setting for message inputs
3716SAMLight09.12.2022FeatureExecute configured pre- and post-jobs in parameter finder
3755SAMLight05.12.2022FeatureNew laser type Fujikura non-continuous auto latch
2340SAMLight01.12.2022BugfixUSC-2 - Redpointer delay
3749SAMLight30.11.2022BugfixCCI Date Time Format setting problems
3687USC-3 Firmware25.11.2022BugfixChanging the stepper factor of an axis will not recalculate other settings that are dependent on it
3740SAMLight18.11.2022FeatureNew CCI constants to move entities in the job list
3737SAMLight18.11.2022FeatureAdd new CCI Commands for File-Print
3597SAMLight28.10.2022Bugfixsc_timer Entity only functional for Head 0 in MultiHead
3717SAMLight25.10.2022Bugfix2D Splitting - a problem with the option 'Automatic Start Position'
3686SAMLight24.10.2022FeatureOption of using % instead of Watt for the laser power for non-CO2 laser types
3715SAMLight12.10.2022BugfixMissing segments in 2D Splitting
3698USC-2 Firmware06.10.2022FeatureUNF RAM management
3704SAMLight05.10.2022BugfixSAMLight view problem with "khmer" language
3713SAMLight30.09.2022BugfixCCI ASCII mode with codepage other than system default does not send an answer if resultstring is empty
3702SAMLight23.09.2022BugfixCCI set and get BitmapLineIndexStep does not work.
3700SAMLight19.09.2022FeatureNew CCI constant to check the current license options
3701SAMLight13.09.2022BugfixRTC4 Unwanted pauses while marking grayscale bitmaps
3694SAMLight12.09.2022FeatureA new CCI constant to check if a poly line is closed.
3697SAMLight05.09.2022FeatureLog connection closure of TCP ASCII connection (CCI)
3695SAMLight05.09.2022Bugfixz-value of previous split job is transfered to non split job when using mark trigger window
3696SAMLight05.09.2022BugfixSplitting option Keep Mark in Progress Active disables MIP completely in non split job with mark trigger window
3693SAMLight31.08.2022BugfixRTC5, RTC6 With inverted red pointer the red pointer is active after SAMLight start
3685SAMLight18.08.2022BugfixAfter man adds or cancels nonsplittable property of control objects and saves the job, this action will not take into effect
3671SAMLight01.08.2022BugfixSerial Number inside of Group with Beat Count is not displayed correctly
3676USC-3 Firmware01.08.2022BugfixY values for HEAD2 differ for MOTF and Wobble
3676USC-2 Firmware01.08.2022BugfixY values for HEAD2 differ for MOTF and Wobble
3672SAMLight22.07.2022BugfixAt switches of User<->Admin, job will disapear or changes to other job in SAMLight
3670SAMLight22.07.2022BugfixWhen Admin switches to User, the property page is inherited from Admin
3664SAMLight22.07.2022BugfixBackground Camera Settings goes to default status, when SAMLight restartet
3651SAMLight18.07.2022BugfixPosition of the toolbars are not saved
3660SAMLight28.06.2022BugfixScanahead delay (negative) value changes every time the dialog is reopened
3653SAMLight17.05.2022BugfixNew CCI constants for ScWaitForInput and ScSetOutput
3646SAMLight05.05.2022BugfixBackground camera cannot be activated via toolbar icon after first start of SAMLight
3647SAMLight02.05.2022BugfixRehatch all removes hatch enable state of sub group elements.
3638SAMLight22.04.2022FeatureCCI command to activate MultiHead spitting
3628SAMLight22.04.2022BugfixMultiHead 1D MOTF splitting with Entity based splitting thows "galvo out of range" for entity outside of Head0
3635SAMLight20.04.2022BugfixCopying pens can erroneously link them together until the next SAMLight start
3617SAMLight13.04.2022BugfixMark lines as dots creates a maximum of 1000 points for each line
3609SAMLight11.04.2022BugfixRotation point (RMOTF) is set to x=0, y=0 after reboot of the card
3608SAMLight22.03.2022Bugfixuse arcsec for angular axis of motion tpye 13
3528SAMLight22.03.2022Featurex-based numbering system for serial numbers in Flash
3616SAMLight21.03.2022FeatureCreate ScLine2D via Client Controll interface
3615SAMLight17.03.2022FeatureAdd Mitered Edges for neg. NumLoops in the Hatch finder
3607SAMLight02.03.2022BugfixRedpointer in ParameterFinder is stopped when I/O error bit is set, even if "Stop RedPointer" is not set
3606SAMLight02.03.2022BugfixInvert flag for Redpointer reacts only on Digi_Out_2 of Extension1 not of Laser connector for RTC6
3610SAMLight28.02.2022BugfixMissing line shift for bidirectional grayscale bitmap in drill mode with jump over blank pixel
3603SAMLight15.02.2022BugfixDXF Reimport does not keep EntitiyInfo for Styles
3586SAM11.02.2022BugfixMissing MOTF reset between trigger markings in flash
3592SAMLight09.02.2022BugfixMutliInstance strings in wrong language

Version 4.0.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
3557SAMLight09.10.2023FeatureNew user level privilege "Show pens (if no edit)"
3493SAMLight12.04.2023FeaturePowermodulation during Drilltime
3369USC-3 Firmware08.03.2023BugfixTRB command shifts vector and bitmap differently
3371SAMLight08.03.2023BugfixMultiHead error message with MultiCard flag in USC Server
3374SAMLight08.03.2023BugfixSecond protected (re-)import resets the entity matrix
3375SAMLight06.03.2023FeatureExtend Report XML - Log Mark Stop
3390SAMLight02.03.2023BugfixPosition of human readable text is wrong for Code 39 Ex with Full ASCII and 2of5 Ex with interleaved mode
1479SAM02.03.2023BugfixBarcode Text checkbox is not activatable for some barcodes that allow text
3388SAMLight02.03.2023BugfixSize of text increases for rotated text with one fixed dimension when text is changed
3409SAMLight02.03.2023Bugfix"No Line Increment" does not work in usc2 advanced bitmap mode
2198SAMLight02.03.2023BugfixSetting entity to nonmarkable and then back to markable activates mark contour/hatch flags
3426USC-2 Firmware02.03.2023FeatureForce Encoding Mode for QR Code Ex
3428USC-3 Firmware02.03.2023FeatureForce Encoding Mode for QR Code Ex
3429SAMLight02.03.2023BugfixParameter Finder value for parameter 2 is applied to wrong type
3434SAMLight02.03.2023Bugfix'Enable scanner bitmap' on bitmap proberty page gets lost when text is changed to space
3433SAMLight02.03.2023FeatureNew CCI Constant NonMarkable
3439SAMLight02.03.2023BugfixProperty page flashing
3451SAMLight02.03.2023BugfixSAM3D Styles mapping with from - to not possible for reversed slicing
3458SAMLight02.03.2023BugfixJPT CW Mode Flag not saved
3391USC-3 Firmware02.03.2023Featureb&w bitmap marking with exchange in Flash
3430SAMLight02.03.2023Bugfix"Special Laser Paramter" category in Parameter Finder is always empty
3399SAM02.03.2023BugfixMultiple bitmaps in one flash job do not work
3422SAMLight02.03.2023FeatureForce Encoding Mode for QR Code Ex
3469Tools02.03.2023FeatureFont Converter should allow point objects
3474SAMLight02.03.2023FeatureShow dongle number in SAMLight for MultiInstance
3447USC-3 Firmware02.03.2023FeatureNew FCI command STAT
3496SAMLight02.03.2023FeatureKeep aspect ratio also available for radial text
3494SAM02.03.2023BugfixScSCIGetWorkingArea always returns 0 for YMax
3491SAMLight02.03.2023FeatureHide "react to external trigger" checkbox and string for USC-1 and RTC cards in ScMOTFOffset entity
3466SAMLight02.03.2023BugfixMark Dialog does not open in MultiCard if first card is in JobIOselect mode
3502SAMLight02.03.2023BugfixActiveCard=1 is lost when re-initializing RTC dlls
3486USC-3 Firmware02.03.2023BugfixCard stops responding if too many flash jobs are uploaded and they reach a particular size
3527SAMLight02.03.2023BugfixRTC can skip commands if special laser type features are used
3529SAMLight02.03.2023BugfixJob execution delay is not inserted when downloading flash jobs
3554SAMLight02.03.2023BugfixError "No valid license for MultiHeadOpticModule" when using MultiCard
3573SAMLight02.03.2023BugfixPulse Length cannot be set with laser type 241-1 (Maxphotonics)
3446SAMLight02.03.2023FeatureHead-dependent setting of the wavelength factor for MultiHead systems
3531SAMLight01.03.2023BugfixMultihead + MOTF + independent trigger mode MOTF compensation is only active for the first marking
3541SAMLight01.03.2023BugfixDecrease size of UNF-attached SJF files
3168SAMLight22.07.2022FeatureIPG type G Interface
3418SAMLight29.06.2022FeatureInactivate mark dialog in SAMLight if marking is started via CCI
3536SAMLight29.06.2022BugfixMultihead + AutoSplitMode activated -> imported entity(.bmp) rotation has problem when autosplit activated
3503SAMLight29.06.2022BugfixHome Position is disabled for Homing during startup and is not set after finish the Homing (Motion Type 8)
3587SAMLight29.06.2022Bugfix1st split part is not marked when started with external trigger - Mark-Trigger
3347SAMLight29.06.2022Bugfixwrong scaling of Quiet Zone for DataMatrix Ex with "Inverted Cellmode" when barcode is scaled
3380SAMLight13.05.2022BugfixMinimum point distance for DXF splines is too large
3389SAMLight19.04.2022FeatureImplementation of CCI commands for splitting
3352USC-3 Firmware24.03.2022Featurenew FCI commands OUT / IN to set/get all 16 outputs/inputs with a mask optionally during marking
3423SAMLight18.03.2022FeatureOption to switch homing during startup on/off for motion type 13
3420USC-2 Firmware20.01.2022BugfixDataMatrix Ex with GS1 encoding does not allow extended ASCII characters
3581SAMLight18.01.2022BugfixMissing MIP during marking with external trigger after usage of "KeepMarkingActive" flag in splitting
3577SAMLight14.01.2022FeatureAdd ability to specify TextCharSpacing and TextLineSpacing in [mm] via CCI
3580SAMLight14.01.2022BugfixFile type necessary for loading job
3576SAMLight23.12.2021BugfixLimit of 999 Watt for PowerMap for CO2 Laser
3546USC-2 Firmware25.11.2021BugfixFCI Command OF does not work for CO2 laser
3546USC-3 Firmware08.11.2021BugfixFCI Command OF does not work for CO2 laser
3548Installer03.11.2021BugfixInstaller might wait indefinitely while installing fonts
3415SAM29.10.2021BugfixAfter doing homing with USC-1/2/3 and Stepper type 08, an error message occurs 'Output is executing'.
3530SAMLight29.10.2021Featurenew laser type for JPT DPSS laser
3515SAMLight26.10.2021FeatureAdd special laser tab of 500-0 to user rights of Pen Advanced
3511SAMLight21.10.2021BugfixSubgrids always reset after press «ok» in «settings/system» window
3510SAMLight21.10.2021BugfixIn the settings of SAMLight Background Camera, after switching camera type, SAMLight muss restart to take into effect.
3535SAMLight21.10.2021BugfixMultihead + AutoSplitMode activated -> Mark Flags in bitmap extended will not be saved
3514SAMLight06.10.2021FeatureReset serial number on time shift change
3519SAM29.09.2021FeatureAllow Laser serial RS232 of laser type IPG YLPP 589 to run with USC-Card RS232
3521USC-3 Firmware24.09.2021FeatureDecrease SCN process time
3520USC-2 Firmware24.09.2021FeatureDecrease SCN process time
3513SAMLight13.09.2021BugfixScMarkEntityByName always marks whole job when Mark Dialog is open
3456USC-3 Firmware08.09.2021Feature3D surface ring and sphere for Optic 3D in Flash - dynamic serial number
3449SAM07.09.2021FeatureInterpret return code of exe objects and stop marking on specific code
3490SAMLight20.08.2021FeatureCCI commands for SPI G4 waveform and cw
3495SAMLight18.08.2021FeatureAllow DirectShow to be used for accessing cameras
3501SAMLight18.08.2021BugfixCCI SaveView2DAdjustableDPI does not work
3488SAMLight13.08.2021FeatureAllow values for ScTimer entity smaller 1ms
3487USC-3 Firmware13.08.2021FeatureNew FCI command DF to set defocus in Flash
3362SAM13.08.2021FeatureAdd an option for Optic3D to display the optical limits when operating above or below the z=0 working area
3364SAMLight13.08.2021BugfixReturn value of ASCII CCI command 'ScCciShowApp' is incorrect.
3485SAMLight02.08.2021FeatureAdd new config option to stepper mode 14 to always move each axis individually
3121SAMLight22.07.2021BugfixChanges of existing points in the pen pixel map are not saved
3470SAMLight22.07.2021BugfixBarcode Tilde Mode issues when encoding "~"
3470USC-3 Firmware16.07.2021BugfixBarcode Tilde Mode issues when encoding "~"
3478USC-2 Firmware15.07.2021BugfixDAC_A and DAC_B are 20% too low
3186USC-3 Firmware15.07.2021FeatureUSC-3, flash Z translation of the TRB FCI command
3467SAMLight15.07.2021BugfixSpecial Laser Parameter is missing for laser type 588-3
3465SAMLight14.07.2021BugfixMultiCard Ramping Settings available on all Heads.
3363SAM02.07.2021FeatureHPGL export should also export pointclouds
3468SAMLight02.07.2021FeatureMessage Input to detect Overflow MOTF Offset
3452USC-3 Firmware29.06.2021FeatureDefocus in flash for USC-3
3461SAMLight29.06.2021BugfixOptic3D Z lookup table entries are sorted incorrectly if distance between two entries is < 1mm
3400SAMLight01.06.2021FeatureBackground camera for SAM3D
3417SAMLight07.05.2021FeatureNew CCI command to get the state of the mark dialog (open / closed)
3424SAMLight28.04.2021FeatureSwitch laser frequency limit for Min/Max dialog to 8MHz for RTC cards
3413SAM27.04.2021FeatureBarcode 'tilde' ~ feature now available for all Barcodes which support this.
3420SAM14.04.2021BugfixDataMatrix Ex with GS1 encoding does not allow extended ASCII characters
3403SAM13.04.2021BugfixMotion type 13 ( Isel Can-Api ) could not read it's settings file
3410USC-2 Firmware08.04.2021FeatureAdd flag to clear buffer upon serial number reset with FLAGS
3394SAMLight30.03.2021FeatureAdd new CCI Constant to set the checkboxes Adapt and Associate in Array Copy
3398SAM16.03.2021BugfixMoves on STL with no distance get dropped, possibly resulting in missing laser off operations
1547SAMLight08.03.2021BugfixUSC-2 Head2 is deactivated when USC-2 card is disconnected and software starts in demo mode
3368USC-3 Firmware04.02.2021BugfixUSC-3 red pointer in flash (RP 1) does not work for infinite looped unfs
3351SAMLight02.02.2021Bugfixfiles not found for RTC6 - Driver version 1.7.7
3345USC-3 Firmware21.01.2021FeatureFCI command for ScMoveAbs
3348SAMLight18.01.2021BugfixBarcodes with inverted cell mode and activated quiet zone get wrong offset in flash mode if an optic rotation is active

Version 3.9.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
3328SAMLight17.03.2023Bugfix"Mark->Increment/Decrement->SerialNumber by" does not work for serial numbers with global sequence
3339SAMLight17.03.2023FeatureShow only current entity list
3323SAMLight08.03.2023FeatureExtend font editor option to add further characters
3299SAMLight08.03.2023FeatureFrequency value with more than four precision digits for special laser types
3302SAM08.03.2023FeatureOption to use Laser_B as FPK in CO2 mode
3292SAM02.05.2022BugfixQRCode Ex "Version" auto detect does not always work.
3238SAM21.04.2022BugfixBitmap split under Multihead did not work.
3106SAM13.04.2022FeatureAllow faster Bitmap marking up to 800 kHz with RTC6
3350SAM11.08.2021FeatureAllow set of 'Max. Frame Rate' for webcam module
3115SAMLight12.04.2021BugfixSAMLight crash/error while importing big .bmp file
3288SAMLight06.04.2021BugfixCCI ScTranslate HumanreadableText wrong displayed
3267SAMLight09.02.2021FeatureAdd a preview window that contains the current layer job
3285SAMLight08.01.2021FeatureNew CCI Command ScSetOutline 2D and 3D
3303SAMLight22.12.2020FeatureLine Spacing/ Char Spacing can be set in % or SAMLight Unit
3306SAM21.12.2020FeatureDo not automatically switch between usc1/usc2 cards when loading a settings file
3264SAMLight21.12.2020FeatureContour marking order changeable for SAM3D-> Style-> Numloops
3250SAMLight21.12.2020FeatureHidden status cannot be get by scComSAMLightClientCtrlLongDataIdEntitySetAsHiddenEntity
3282SAMLight21.12.2020Featureautomatic serialization of serial numbers with bitmaps
3322SAMLight02.12.2020FeatureFreeze time when resetting all serial numbers in property page and extras - reset
3318SAMLight30.11.2020Featurenew digitizer
3325SAMLight26.11.2020Bugfixmultihead after opening the trigger window for the second time just one USC-1 card can be triggered
3284SAMLight17.11.2020FeatureNew sc_simple_straight_speed font
3252SAMLight15.10.2020FeatureSelection of chucks via drop down menu
3277SAMLight13.10.2020FeatureResplit after mark only if data has been changed
2477USC-3 Firmware01.10.2020FeatureGrayscale bitmaps in USC-3 flash mode
3152SAMLight29.09.2020FeatureNew hatch parameters "Hatch Loop" and "Loop Angle"
2191SAM29.09.2020Bugfixstepper type 14 pressing stop button during homing leads to different errors.
3224SAMLight25.09.2020FeatureAllow 4MHz also for JPT laser tpye with USC-3
3241SAMLight15.09.2020BugfixIn case EntityBasedSplitting, BarCode12Chars2d could not be used.
3245SAMLight15.09.2020BugfixStore to flash via cnc (sjf->cnc->unf) does not work
3251SAM14.09.2020BugfixDirect 'Go' in Motion Property Form for Stepper Type 08 did not work for more than one axis.
3249SAM10.09.2020Featurebetter & more meaningfull description for error message "Init returned error 0x00000102" in case of necessary RTC driver update
3246SAMLight09.09.2020FeaturePartCounterMode Disable Count for Redpointer-/ Nonmarkable Entites
3244SAMLight04.09.2020BugfixSAMLight crash on entering Settings - System if FCM is active
3239SAMLight01.09.2020Bugfixnonsplittable entity does not work with 1D Mark on the Fly splitting
3176SAMLight26.08.2020Featurex offset and ring center options for ring splitting tilt compensation
3221SAMLight03.08.2020FeatureAdd CCI command to save unf file from flash to disk
3220SAMLight03.08.2020FeatureNew flag for successful creation of empty barcode with ScCreateEntity
3216USC-3 Firmware31.07.2020BugfixJLA only automatically appends ".unf" to filename if filename is at least 5 characters long
3214SAMLight31.07.2020BugfixDuplication of error message with USB Dongle if USC card missing
3223USC-3 Firmware30.07.2020FeatureNew Telnet connection replaces old one for USC-3
3212SAMLight29.07.2020BugfixFor RTC5, MIP is not activated if PartCounter Mode and Selected is active
2473USC-3 Firmware27.07.2020FeatureRead USC-3 settings by SAMLight and sc_setup
3202SAMLight16.07.2020FeatureUser privilege for "Increment/Decrement/Reset Sequence/Serialnumber"
3210SAMLight13.07.2020FeatureAllow import of *.xlsm files for serial numbers
3125SAMLight09.07.2020FeatureSerial Number .csv import
3179SAMLight07.07.2020FeatureAddition of new Tab for Splitting in Settings -> System
3200SAMLight07.07.2020FeatureAllow pen change for protected entity (scComSAMLightClientCtrlImportFlagProtected)
3129SAMLight07.07.2020FeatureRedesign and optimization of resource dialog in sc_setup for unicode translation
3166SAMLight07.07.2020FeatureBold selection box
3198SAMLight07.07.2020Bugfixcci return of ScMarkEntityByName in cci log is 1 when it should be 0.
3184SAMLight12.06.2020BugfixReferencing of serial number / date time not working if reference is barcode
3177SAMLight02.06.2020FeatureNew CCI command for "Total Diameter" and "Mark Angle" in BMP continous move and mark
3165SAMLight25.05.2020BugfixUSC-1 home jump for SAMLight start is missing
3167SAMLight14.05.2020BugfixSAMLight Entry Bitmap Import
3131SAMLight12.05.2020BugfixClientCtrlEx Import .bmp via memory rendering and positioning problem
2829USC-3 Firmware08.04.2020FeatureCreate identical flash fonts only once
3003SAMLight23.03.2020Feature4MHz hot key information on output frequency
3055SAMLight10.03.2020BugfixBackground Camera focus, camera switching
3079SAMLight16.01.2020FeatureInvert a single Opto_Out via CCI

Version 3.9.0

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
3181SAMLight29.09.2020Bugfixdxf1 import with "Keep Order" flag does not apply new spline resolution
3212SAMLight29.09.2020BugfixFor RTC5, MIP is not activated if PartCounter Mode and Selected is active

Version 3.8.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
2929USC-2 Firmware26.04.2021BugfixFCI command LC does not work in Flash mode with external trigger.
2095SAMLight26.04.2021BugfixSVG import font generation misalignment
3049SAMLight26.04.2021BugfixImproved beam compensation puts hatch always on z=0mm
3072SAM26.04.2021FeatureAdd option to use windows default "Precision Select" cursor in view2d
3047SAMLight17.12.2019FeatureImplementation of new CCI command to get laser type, laser version and optical field axis states
3074SAMLight16.12.2019FeatureDisable Splitting by CCI command
2660USC-3 Firmware12.12.2019FeatureIncrease maximum Laser_A frequency up to ca. 4 MHz
3051SAMLight06.12.2019Featurenew RTC5/6 SkyWriting mode implemented
3063SAM06.12.2019FeatureAdd duplicate and delete to object list context menu
2963SAMLight06.12.2019FeatureAllow Prolines Generation via new menu entry in Sam3D (scaps intern and one customer)
3065SAMLight06.12.2019FeatureDrag & Drop of job-files directly into SAMLight to load them in;
3045SAMLight06.12.2019BugfixError of precision of comma value during slicing in SAM3D
3013SAMLight06.12.2019FeatureSignal if vectors are too short for current speed in simulation
3043SAMLight06.12.2019BugfixRS-232 connection of USC cards did not work after SAMLight exit
3070SAMLight04.12.2019BugfixStatus outputs Software started OptoOut and DigiOut goes low if settings are opened
3019USC-3 Firmware28.11.2019FeatureAnalog In Offset for Z
2889SAMLight22.11.2019FeatureAuto-Apply font for a better font preview of text entities in SAMLight
3016SAMLight22.11.2019BugfixShutter control opens shutter during Red Pointer.
3036SAMLight22.11.2019BugfixMultiHead independent trigger mode does not work on 2 USC-1 cards
2886SAMLight21.11.2019FeatureShow file preview in SAMLight->File->Import dialog
2994SAMLight18.11.2019FeatureDrill Keine CW-mode Anzeige
3008SAMLight14.11.2019BugfixLoading ,sjf with splitting view problem
2981SAMLight12.11.2019BugfixSAM3D CCI Mark Selected Only Tag works only after the mark dialog has been opened once
2998SAMLight12.11.2019BugfixSAMLight crashes if a split-job is changed while redpointer is running
3002Tools12.11.2019FeatureSAMLock make the previous password invalid if time is manipulated
3020USC-2 Firmware11.11.2019FeatureNew FCI command to get/set output invert states.
3040SAMLight06.11.2019BugfixProblems with DXF import in SAMLight
3039SAMLight22.10.2019BugfixSerialNumber is not displayed in SAMLight View2D when uploaded in jobfile to flash card by SAMLight Client Control
3032SAMLight22.10.2019BugfixQuickly switching input values in SamLight JobIO mode with activated trigger window may not select the new job
2685SAMLight01.10.2019BugfixParameter finder dialog is not complete with Windows display language Korean
3018SAMLight01.10.2019BugfixCCI command ScLoadJob fails after stopping a split job with ScStopMarking
2967SAMLight20.09.2019BugfixSAMLight Flash Dialog, External Trigger checkbox not updated when using ET command
2932SAMLight20.08.2019Featureshowing JobIOSelect mode in status
2960SAMLight20.08.2019Bugfixswitching between 2 head in Pen property page triggered a breakpoint/ USC-3
2935SAMLight20.08.2019BugfixWrong path and file name for CNC export
2938SAMLight20.08.2019BugfixValue of ScGetStringValue is missing in the sc_cci_debug.txt log file
2694SAMLight20.08.2019FeatureBackground camera tool for SAMLight
2993SAMLight14.08.2019FeatureAdd CCI command 'activate background camera'
2980SAM30.07.2019BugfixMultibyte strings in e.g. chinese were potentially not saved correctly in settings file.
2972SAMLight29.07.2019BugfixChinese resource, PowerMap -> Frequency unit is wrong.
2976SAMLight25.07.2019Bugfixwrong paths passed to RTC3 dll
2978SAMLight25.07.2019BugfixProblem with multi-line text
2973SAMLight22.07.2019BugfixSAMLightJobIoSelectionMode, trying to mark crashes SAMLight
2936SAMLight11.07.2019FeatureNew Splitting feature Split alignment for 'Angular Splitting', '1D Planar Splitting' and 'Ring Splitting'
2958SAMLight08.07.2019BugfixCCI ScMoveAbs() does not work anymore, if running with red pointer before.
2857SAMLight05.07.2019FeatureCheckbox for duplication of scanner signals to Head2 for USC-3
2956USC-3 Firmware03.07.2019BugfixG-Code converter of USC-3 always convert for CO2 lasers
2919SAMLight03.07.2019BugfixMotion Stepper Type 14, ScMotionControl as nonsplittable post mark, homing of one axis results in homing of all axes
2275SAMLight03.07.2019BugfixUSC-1 - OptoOuts cannot be changed in Driver Settings
2914SAMLight24.05.2019FeatureHighlight field 'rotation' if MOTF is enabled
2926SAMLight23.05.2019FeatureNew DataWizard CCI commands
2937SAMLight23.05.2019FeatureIncrease FCI Timeout in SAMLight -> Extras -> Flash
2928SAMLight23.05.2019BugfixCCI ExecCommand WizardCreateSinglePenGroup does not always delete empty folder
2922USC-2 Firmware14.05.2019FeatureScMotionControlGo in flash
2911SAMLight10.05.2019FeatureRotate STL around STL zero point (0,0,0) in STL projection dialog
2852SAMLight09.05.2019FeatureCNC Export independent of Flash License
2854SAMLight06.05.2019FeatureOptic3D - 3D Surfaces - Ring (Torus, Donut)
2902SAMLight06.05.2019BugfixAll toolbars are disabled on startup of SAMLight
2917SAMLight03.05.2019FeatureCreatePenGroup for a specific pen via CCI
2908SAMLight03.05.2019FeatureNo additional refio check during homing for refmode 11 and 44 for motion stepper type 14
2892SAMLight29.04.2019FeatureSave/Load splitting parameters inside *.sjf job in File->JobProperties
2900SAMLight29.04.2019BugfixNonsplitable Entity Post Mark is not executed
2905SAMLight26.04.2019BugfixNo marking after homing in job (motion type 8)
2888SAMLight08.04.2019BugfixSAM3D, redpointer increments ActNum
2887SAMLight08.04.2019FeatureImplement DataWizard Create Pen Groups as CCI command
2859SAMLight01.04.2019FeatureShow Optic -> Rotation for RTC cards
2869SAMLight01.04.2019Bugfix'Laser active' and redpointer signal of RTC5 card of the LASER connector does not work correctly.
2885SAMLight01.04.2019BugfixProblem with head assignment for 'Mark only selected' for MultiCard setup
2844SAMLight28.03.2019BugfixSAM3D, redpointer is disabled
2871USC-2 Firmware26.03.2019FeatureFCI command TX working on more than one serial number with the same entity name
2862SAMLight26.03.2019BugfixBMPs declared as background entities are considered during BMP continous mark and move
2874SAMLight25.03.2019Bugfix3D View dialog cannot be closed in SAMLight demo mode
2873SAMLight25.03.2019BugfixVar. Angle for active "Use Styles for Layer" with inactive "3DView"
2853SAMLight25.03.2019BugfixOpening of the Settings - System dialog closes TCP connection of CCI
2877SAMLight25.03.2019FeatureCommand line parameter '/noclose' to prevent SamLight from closing except via CCI
2867SAMLight20.03.2019FeatureCCI command for Optimize jumps in data Wizard
2860SAMLight20.03.2019BugfixUSC-3 Error message, problem with firmware update
2847SAMLight20.03.2019FeatureCreate new entity in SAMLight by CCI command ScCreateEntity()
2876SAMLight20.03.2019FeatureImplement DataWizard ClosePolylines as CCI command
2868SAMLight12.03.2019BugfixSAM3D, S3D jobs can get corrupted
2843SAMLight05.03.2019BugfixScMarkEntityByName problem when redpointer is running
2826SAMLight05.03.2019BugfixScMarkEntityByName in demo mode
2830SAMLight12.02.2019BugfixMark Lines as Dots does not work when Perforation is enabled
2828USC-3 Firmware12.02.2019FeatureUNF RAM management
2824SAMLight04.02.2019Featurepreview of job file per CCI

Version 3.7.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
2569SAMLight17.12.2021FeatureSAM3D reverse slicing below Z = 0 mm for ablation applications
2789SAMLight06.12.2019BugfixProblem enabling Marking on the Fly
2180SAMLight06.12.2019BugfixJobsToolbar StopProcess is not executed
2229SAMLight12.11.2019Featurepen changing causes resplitting without asking
2579SAM18.10.2019FeatureDo not open Driver Settings dialog in sc_setup if Flash JobIOSelectMode is active
2571SAMLight27.08.2019Bugfixnew set RTC5 correction file is not applied in Card tab at SAMLight Settings->System
2798SAMLight17.01.2019Bugfix100s timeout for marking via remote control (also in SAM3D, CCI)
2758SAMLight03.01.2019BugfixHomeJump flag gets disabled automatically in MultiHead or MultiCard mode
2244SAMLight02.01.2019Featuresc_setup store button should behave like SAMLight store button
2811SAMLight27.12.2018FeatureScSliceFromTxt() as CCI command for SAM3D
2808SAMLight17.12.2018BugfixRehatch all should update the scanner bitmap as well.
2766SAMLight14.12.2018FeatureChange direction of offset for Analog In via sign of gain
2807SAMLight14.12.2018BugfixBitmap dialog gets back to default values if EntityInfo is changed.
2805SAMLight11.12.2018BugfixHatch and pen assignment for reverse slicing by *.txt file in SAM3D does not work properly
2795SAMLight10.12.2018Feature"override_string.txt" does not change the string in Power Map
2799SAMLight29.11.2018BugfixBlack square for imported *.tif files in SAMLight
2764USC-2 Firmware26.11.2018BugfixMotion axes make noise with stepper mode 14 (jitter problem).
2760SAMLight26.11.2018FeatureTop level only entity-based splitting for 2D planar splitting
2791SAMLight26.11.2018BugfixCCI problem with scComSAMLightClientCtrlLongDataIdEntityOpticFlags hatch flag is set independent from EntityName
2794SAMLight19.11.2018BugfixPosition of main window is not restored for some extended monitor configurations
2493USC-3 Firmware19.11.2018FeatureNew wobble mode with adjustable wobble function
2778USC-2 Firmware29.10.2018BugfixQuotation marks (") are not displayed in Flash for serial number - FCI command TX
2781SAMLight29.10.2018BugfixSTORE button for USC-3 does not work without 'Flash' license (Error saving current SamLight settings to USC3)
2783SAMLight29.10.2018BugfixField size 0 due to incorrect sc_resource_settings.sam
2767SAMLight17.10.2018FeatureRed pointer always active at home position
1771SAM15.10.2018BugfixUSC New 'FTheta Correction' feature to improve XY accuracy of 3D marking if F-Theta is installed
2762SAMLight12.10.2018BugfixSome characters are not marked in flash (missing o)
2409SAMLight05.10.2018FeatureInclude hatch enable checkbox to defaults
2720SAMLight05.10.2018FeatureSave/Load 3D surfaces in Job file
2756USC-2 Firmware04.10.2018BugfixG-Code (CNC) converter of the USC-2 via FCI command CGF does not work
2759USC-2 Firmware02.10.2018BugfixNo HomeJump sequence if home jump is deactivated
2704SAMLight01.10.2018FeatureMark flag scComSAMLightClientCtrlMarkFlagHideOutput does not work in SAM3D
2753SAMLight01.10.2018BugfixLaserports are not working in the PowerMap dialog
2755SAMLight28.09.2018FeatureAdd z timelag for RTC6 with excelliscan (set_timelag_compensation)
2718SAMLight31.08.2018Bugfix'Copy selected head to' button in sc_setup.exe does not copy pen settings
2712SAMLight31.08.2018FeatureAdd support for a combined serial number and datetime format string
2717SAMLight20.08.2018BugfixMotfMul will not be updated if the fieldsize is changing
2679SAMLight08.08.2018FeatureUSC-3, flash Add error message, when generating a UNF with a dynamic object on a 3DSurface
2714SAMLight06.08.2018FeatureUse Min/Max frequency limits in the PowerMap dialog
2657SAMLight03.08.2018BugfixScTimer object does not work after it has been cancelled
2572SAMLight10.07.2018BugfixExitTriggerMode and ScStopMarking are not shown in sc_cci_debug.txt
2700SAMLight09.07.2018BugfixMark loop count does not work for character based splitting
2680SAMLight08.06.2018BugfixSAMLight crash opening SC_Layer in object list
2675SAMLight05.06.2018BugfixLine Step index has wrong value if an old job file is loaded in the latest release of SAMLight
2644SAMLight22.05.2018FeatureStatic Z offset for dynamic objects in standalone mode
2529SAMLight09.05.2018BugfixServer reports no card is connected, although a card is connected
2590Tools09.05.2018Bugfixsc_corr_table, error message 'USC-2 settings cannot be used for a USC-1/-3 card'
2605SAM08.05.2018FeatureReset cmd list in mark preview window to empty for every new mark preview call.
2654SAMLight08.05.2018BugfixEXE object within job will be executed although job was cancelled by software
2614SAMLight04.05.2018FeatureAdd laser type 241-1 for Maxphotonics with adjustable pulse length.
2645SAMLight04.05.2018FeatureNew GS1-Datamatrix barcode with enhanced features
2568SAMLight04.05.2018FeatureGUI changes SerialNumber format and DateTime format
2615SAMLight09.04.2018BugfixError message home position not inside valid field even if home position is not enabled
2626SAM06.04.2018Bugfixpossible MDrive connection problem because of RS232-USB-Adapter set to RTS_CONTROL_ENABLE in SAM library
2621Installer22.03.2018BugfixSAMLight installation error 'Registration of the External Modules failed!' on new system
2219SAMLight12.03.2018BugfixWrong picture size after import for some file formats like *.jpg or *.png in SAMLight
2611SAMLight12.03.2018FeatureAdd defocus delay for RTC5 and RTC6 cards
2613SAM09.03.2018BugfixRTC6 LaserOnDelay and RTC6 LaserOffDelay we too big by factor 32
2602SAM22.02.2018FeatureUse Circle/Ellipse for cells in DataMatrixEx - Cellmode
2592SAM15.02.2018FeatureBitmap mode Gray Advanced - round the frequency to 1/n*100ns
2591SAM14.02.2018BugfixBitmap mode Gray Advanced - frequency dependent DAC_A to LaserGate delay
2578SAMLight14.02.2018FeatureCCI command for MOTF arrow button
2538USC-3 Firmware14.02.2018Bugfixflash command LDG does not work.
2550SAMLight30.01.2018FeatureText2D line wrapping (carriage return)
2581SAM30.01.2018FeatureDrill Frequency cannot be set directly for IPG laser mode
2596SAMLight30.01.2018BugfixSAMLight freezes on right click some entities in View2D (context menu)
2511SAMLight23.01.2018FeatureChanging between property pages impossible if window at negative desktop coordinate
2514SAM23.01.2018BugfixUnder Windows10, shutdown of Sam Top Level App may fail due to bad memory access
2526SAMLight23.01.2018BugfixDo not recalculate split does not work for 1D Mark on the Fly splitting
2577SAMLight22.01.2018Bugfixsc_corr_table deleting worst point could be on wrong index
2585SAMLight22.01.2018BugfixDon't show and uncheck 'IPG - EmissionEnable' groupbox for other lasers
2512SAMLight18.01.2018BugfixCCI changes on serialnumbers are not directly updated in the property page
2515SAMLight18.01.2018BugfixReference count of ObjectListCtrl always runs up, so memory leak when Samlight shuts down.
2582SAMLight18.01.2018BugfixUSC-3 pen defocus does not work if z correction is enabled
2551SAMLight18.01.2018FeatureCCI command for Toolbars box
2563SAM18.01.2018BugfixSome current RS232 SAM/Samlight implementations can fail before.
2584SAMLight18.01.2018BugfixWrong pen was used when a SVG file was imported via CCI to SAMLight
2583USC-2 Firmware18.01.2018FeatureScSetLongValue - scComSAMLightClientCtrlLongValueTypeNewCciErrorReturn

Version 3.6.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
2451SAMLight22.02.2022Featureautomatic z-axis drive when Redpointer ist started
2456SAMLight04.09.2020FeatureScScaleEntityCurPos scales the entity at the current position
2369SAMLight13.05.2020BugfixRTC5 - add delay to set ouput
2327SAMLight13.05.2020FeatureScJump job entity
2431SAMLight13.05.2020FeatureAdd FCI command MUL to change the MOTF multiplier
2513SAMLight04.10.2018BugfixWindows update causes Excel import problem
2455USC-2 Firmware13.04.2018FeatureAdd scanner home jump after initialization of USC-2 when flash commands HP and JPM is defined/enabled
2356SAMLight16.02.2018FeatureChanged splitting handling of protected entites imported by CCI
2355SAMLight16.02.2018BugfixCCI cannot activate MOTF correctly for USC-2
2347SAMLight16.02.2018Featureset MIP Signal low during home jumpe
2002SAMLight16.02.2018BugfixUSC-2+BMP+MOTF strange end mark process
2447SAMLight15.02.2018Bugfix"waiting for external trigger" in trigger mode and mark mode
2450SAMLight15.02.2018FeatureMark selected in SAM3D
2453SAMLight15.02.2018FeatureLaser specific parameter as drop down (e.g. pulse length)
2488SAMLight15.02.2018Bugfixlimited marking speed
2482USC-2 Firmware15.02.2018FeatureNew FCI command LOG to make a USC-2 log file entry.
2565SAMLight14.02.2018Bugfixlaser frequency for entity with Mark Loop Count -1 remains at HomeJump Style frequency for second mark
2573SAMLight14.02.2018BugfixARCSTEPMODE in *.CNC files was ignored by import in SAMLight
2533SAMLight14.02.2018BugfixStatus Output Bit "Waiting for external start" is not reset after marking if Mark is dialog open and marking is started by CCI
2460USC-2 Firmware10.01.2018BugfixG-code circle command G3 does not work correctly when CNC file was uploaded by the usc-server to the USC-2
2540SAMLight02.01.2018FeatureCCI command for Slice Export in SAM3D (CLI)
2575SAMLight28.12.2017BugfixSVG import vectors have disabled PenPath flag
2566SAMLight19.12.2017Featureimplementation of SAMLight Client Control ASCII command ScCciDuplicateEntity(string EntityName, string DuplicatedEntityName)
2561SAMLight08.12.2017BugfixFlash Serialnumber is not proper alligned to Rotation/Offset
2558SAM05.12.2017BugfixRTC6 dll function parameter change leads to SAMLight crash
2554SAMLight28.11.2017BugfixUSC-1 Pen1 settings aren't used when opening Z-Correction dialog with "fire laser with Pen1" checkbox enabled & pressing "Apply"
2545SAMLight23.11.2017BugfixSerial number could not import all formats from excel file
2531SAMLight14.11.2017Featurecreate one single point clould of individual points by data wizzard or group functionality
2534SAMLight14.11.2017Bugfixempty UII barcode in SAMLight job file if save and reloaded
2510SAMLight03.11.2017FeatureOption to not mark a barcode in flash mode.
2527SAMLight03.11.2017BugfixFor 2 axes moved by one motion control entity, simultaneous marking and movement of 2nd axis
2525SAMLight02.11.2017FeatureSamlight is now built with MS VS 2015
2521SAMLight24.10.2017BugfixMissing Windows update for the universal C runtime causes settings mismatch
2501SAMLight20.10.2017FeaturePulse width control of IPG Type E (588-2) with RTC cards
2520SAM20.10.2017BugfixUnder SAM3D, import of slc files was no more working correctly.
2518SAMLight19.10.2017BugfixOptic3D, unwanted moves
2332SAM13.10.2017FeatureUSB driver 12.30 WHQL signed by Microsoft to be Secure Boot compatible
2509SAMLight10.10.2017BugfixSAMLight freezes when leaving toolbar dialog
2489SAMLight10.10.2017BugfixscComSAMLightClientCtrlLongDataIdBitmapMode not for ScWinTextChars2D
2506SAMLight06.10.2017BugfixSAMLight -> Flash command window inactive
2481USC-2 Firmware26.09.2017BugfixFlashmode flag USE_SYNC_BITS is not saved
2449SAMLight22.09.2017BugfixDemo mode disables Optic3D
2486SAMLight22.09.2017FeatureEnable Optic3D, MOTF and Head2 in demo mode.
2459SAMLight21.09.2017BugfixSAMLight crashes for non-defined Index in ScGetEntityOutline
2483SAMLight21.09.2017FeatureTCP ASCII mode code page for client control programming
2438SAMLight18.09.2017FeatureSimplify translation process
2152SAMLight18.09.2017BugfixSAMLight Jobeditor license / command line parameter lead to unexpected handling failures
2480SAMLight13.09.2017Featureinfo text in loading job file dialog
2317USC-2 Firmware04.08.2017FeatureAdd FPK to available g-code commands in USC-2 flash mode
2291USC-2 Firmware01.08.2017BugfixFlash Job Io Selection Mode - Job could be executed without trigger when changing job while marking
2434SAMLight01.08.2017FeatureSelect output pins for ready for trigger and job loaded in flash job io selection mode
2439SAMLight13.07.2017FeatureSAM3D Entity rotation
2436SAMLight04.07.2017BugfixSAM3D SAMLight Client Control command ScRotateEntity3D does not work
2424SAMLight16.06.2017BugfixSL crash for Create multiple Serial Numbers
2422SAMLight08.06.2017Bugfixbug of Text freely editable + Rotate
2408SAMLight30.05.2017FeatureSAMLight does not notice the start of a marking process per CCI
2419USC-2 Firmware26.05.2017BugfixUSC-2, MotfSpeed is influenced by +- sign of MOTF Multiplier
2418SAM22.05.2017FeatureNow, all SAM modules are available for Powershell or Basic script and others.
2415SAMLight18.05.2017BugfixIf opening Samlight mark dialog through CCI, an internal wait time is required to let following cmd's be valid.
2414SAM18.05.2017BugfixCCI cmd 'ScMarkEntityByName()' with param 'WaitForEnd=1' returns too early, if CCI is running in TCP/IP mode.
2413SAM18.05.2017BugfixSamlightClientCtrlEx Cmd ScGetMarkFlags() did not work, if CCI running as TCP/IP.
2398SAMLight18.05.2017BugfixWhen changing motion position within two 1D split markings, new initial position is not updated.
2388SAMLight15.05.2017Featureright-click menu is missing in the barcode input textbox
2401SAMLight15.05.2017BugfixRTC5, 1D MOTF splitt job,out_0 signal goes high before user triggert.
2406SAMLight15.05.2017BugfixWith motion type set to zero ( no motion ), Samlight could crash during shutdown.
2397SAMLight05.05.2017BugfixRingSplitting moves into wrong default position, when 'CenterSplit' is active and mode is fixed with x-axis as split axis.
2391SAMLight05.05.2017BugfixScSamlightClientCtrl(Ex) is not working with powershell
2377SAMLight05.05.2017Bugfixa horizontal line can not be splitted with 1D planar splitting
2385SAMLight05.05.2017FeatureEncoder Distance counter for RTC-5 in SAMLight
2395SAMLight03.05.2017BugfixSAM3D tab missing in Demo Mode
2368SAMLight02.05.2017BugfixBitmap mode Gray Advanced, 'begin with the last line', wrong direction
2362SAMLight26.04.2017FeatureApply pens for CNC (G-Code) import in SAMLight
2387SAMLight25.04.2017BugfixSamlight settings prop page extras could show error message, even error is not locatable on this page.
2386SAM24.04.2017FeatureRadial text with fixed angle to display within did not work for multi line text.
2361SAMLight18.04.2017Feature"Set quantities" in Splitting does not work
2363SAMLight18.04.2017FeatureAllow more than 360° in Ringsplitting / Bitmap Marking
2365USC-2 Firmware03.04.2017FeatureControl Characters (ANSI characters >235) will be interpreted as usual characters in Telnet mode of USC-2
2364SAMLight31.03.2017BugfixSplitting/ Bitmap marking
2352SAMLight09.03.2017BugfixSAMLight JobSelect I/O Mode can overwrite a jobfiles in combination with save job after each mark
2354SAMLight06.03.2017BugfixRS232 communication issue while marking in flash mode
2351SAM06.03.2017BugfixWhen using a drill geometry as ScPointCloud, Sam crashes
2339SAMLight13.02.2017Bugfixkeep marking active output
2338SAMLight10.02.2017BugfixRehatch All does not work under condition redpointer with auto pointer activated
2313SAMLight08.02.2017BugfixBitmap mode Gray Advanced does not support tilted rectangles
2337SAMLight08.02.2017BugfixJobIoSelection poll intervall too high
2329SAMLight01.02.2017BugfixInverted red-pointer bit leads to problems when switching from USC-1 to USC-2 (red pointer and pulse length)
2333SAMLight30.01.2017BugfixSamlight crashes, when loading BmpSplit job, then loading job without BmpSplit, then load BmpSplit job again.
2295SAMLight30.01.2017BugfixStep&Repeat does not work in SAM3D (Settings in menu bar are disabled)
1794SAMLight30.01.2017BugfixCreate One Group destroys far away entities
2310SAMLight27.01.2017BugfixRotary Outermost border
2328SAMLight27.01.2017FeatureAdd 'To All' button for pulse length in pen IPG tab
2294SAMLight26.01.2017BugfixPower save mode does not work for RTC-4
2331SAMLight26.01.2017BugfixIf new job property option is on 'load/save pre post jobs in job file', Samlight crashes, when closing App.
2321SAMLight17.01.2017FeatureSave Job toolbars settings in job file

Version 3.5.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
2161SAMLight30.06.2025BugfixChanging font size when edit Text2D and clicking on Apply
2306SAMLight13.05.2020BugfixMOTF splitting is disabled by loading an other job
2280SAMLight07.06.2019FeatureIncrease maximum duration of ScSetOutput pulse
2204SAMLight24.05.2019FeaturePen perforation tool
2163SAMLight16.02.2018FeatureSAMLight Client Control constant to set Quiet Zone in % and absolut for inverted DataMatrixEx barcode
2130SAMLight16.02.2018FeatureIn SAMLight save settings for Standard I/O mode and Job Select mode, so that after switching old values are set.
2183SAMLight16.02.2018BugfixWhen changing the Enable~ checkbox for DataMatrixEx -> Advanced, then in Flash text is inverted.
2190SAMLight16.02.2018BugfixWrong Lasergate behavior when using ScSerialNumbers2D with Code 128 (2) in a flash job can
2194SAMLight16.02.2018FeatureAdd Flag for MOTF Offset Entities to disable the external trigger for skipping the defined delay
2233SAMLight16.02.2018Feature"All" button for "use vector delay"
2232SAMLight16.02.2018Bugfixradial text has a wrong alignment with mirror X
2192SAMLight16.02.2018BugfixAligment reference position is not rotated in flash jobs (unf)
2225SAMLight16.02.2018Bugfixsc_server.exe error message "Encountered an improper argument"
2297SAMLight16.02.2018BugfixDrill geometry always uses pen1
2307SAMLight16.02.2018Bugfixmark time in flash is much longer than in SAMLight
2235SAMLight16.02.2018FeatureCCI command request for Store button
2111SAMLight15.02.2018FeatureNew feature Import and export functionality for the style feature
2164SAMLight10.01.2018FeatureMarking on the fly overflow feedback for USC-2 cards
2231SAMLight02.05.2017BugfixTiming issues can cause usc2 card settings to flip
2311SAMLight08.12.2016BugfixDate Time Advanced %1y works the same as %2y.
2296SAMLight07.12.2016FeatureGet with scComSAMLightClientCtrlLongValueTypeGetOptoOut DigiOut and StepperOut as well
2305SAMLight05.12.2016Bugfix"Do Not Recalculate Split Lines" problem
2302SAMLight05.12.2016BugfixMotion type 5 (MDrive) command optimizations
2301SAMLight30.11.2016FeatureSave Preview Colors
2171SAMLight04.11.2016BugfixPower map not saved
2286SAMLight25.10.2016BugfixMark Beat Count and Mark Beat Offset does not work for 'Mark as Bitmap' in SAMLight Bitmap rotary
2239SAMLight25.10.2016FeatureAdd new flag 'Keep Manual Splitline Changes' in splitting dialogs
2269SAMLight25.10.2016Featureungroup ScWinTextChar2D
2279SAMLight25.10.2016FeatureXML report log file
2274SAMLight10.10.2016FeatureRTC5 - Improve strings of advanced wobble feature
2282SAMLight10.10.2016BugfixTwo successive points in a point cloud are not marked twice.
2278SAMLight30.09.2016BugfixRed pointer 'individual outline most outer' has problems with lines only.
2277SAMLight30.09.2016BugfixEntity based splitting did not work correctly for 3 last downloads.
2276SAMLight30.09.2016BugfixSAMLight memory leak for Client Control constant scComSAMLightClientCtrlStringValueTypeBmpAlphaBlendPathBmp
1799SAMLight28.09.2016FeatureDisable Mark -> Start -> ext.Trigger checkbox when MOTF is activated
2158SAMLight28.09.2016FeatureText2D - merge character outline and generate single characters
2264SAMLight28.09.2016FeatureRTC5 - Unlock ScMotfOffset and ScWaitForTrigger control objects
2270SAMLight27.09.2016BugfixUSC-2 bitmap raster mode unavailable
2268SAMLight15.09.2016BugfixEntityBasedSplitting could contain non marked item, if text / serialnumber AND other items exist.
2137SAMLight09.09.2016FeatureStepper type 14 - new ref modes without timeout for switch leaving move
2110SAMLight08.09.2016FeatureEnlarge the unicode text box
2250SAMLight19.08.2016Bugfixchange from "mm" to "inch" can not be saved
2242SAMLight05.08.2016BugfixGrouped serial number does not update correctly if marked as bitmap
2248SAMLight04.08.2016BugfixSplitting option 'Center split on current position' could often produce wrong first positioning.
2247SAMLight02.08.2016BugfixChanges regarding Splitting and BmpRotary with Serialnumbers as Bitmap and Barcode as Bitmap.
2238SAMLight29.07.2016BugfixRing Splitting - "Move back to start position" and redpointer issues
2241SAMLight29.07.2016FeatureNew command line parameter /StepperMotionFile
2245SAMLight29.07.2016FeatureImplement MultiHead functionality for SAM3D
2223SAMLight27.07.2016FeatureGenerate dot array for DataMatrixEx in SAMLight
2237SAMLight27.07.2016BugfixMarkPreProcess is not executed when MarkSelectedOnly is enabled
2138SAMLight22.07.2016BugfixSAMLight not responding on startup / Missing password dialog in Windows task bar
2226SAMLight22.07.2016BugfixMulticard job file can't be uploaded to 2. USC-2 Flash card via SAMLight Client Control command ScProcessFlashJob
2230SAM12.07.2016BugfixSAM library could hang forever at startup, e.g. at Windows10 tablet, during setup and more.
2228SAMLight05.07.2016BugfixBmp Rotary with more than one bitmap did not work with Mark Trigger window.
2224SAM21.06.2016BugfixStepper motion type 08 Reference position, if not zero, was calculated and displayed wrong.
2213SAMLight20.06.2016FeaturePreview pops up the MarkOutput dialog, but it should be hidden with MarkFlagHideOutput
2214SAMLight20.06.2016BugfixPrecalculating MarkTime with SeparatedBySemicolon
2200SAMLight20.06.2016Featurejob loaded does nothing in Standard mode
2184SAM20.06.2016BugfixDataMatrixEx barcode cannot code alphanumeric characters according to barcode specification in some cases
2222SAM14.06.2016BugfixUnder 32 Bit OS Windows Vista and higher, deinstallation of driver or software leaves the USC driver installed.
2139USC-2 Firmware08.06.2016BugfixSporadically slow movement of USC-2 after booting
2202SAMLight07.06.2016BugfixSAMLight toolbars are flashing when MarkDialog is open and Message Input with Error Stop Mark is active
2142SAMLight03.05.2016BugfixSingle axis homing - or disabling the homing checkbox within a job control object does not work anymore
2196SAMLight03.05.2016BugfixGeneralSettings, HomePosition is saved before rotation
2147SAMLight02.05.2016BugfixStepper type 14 - homing in standalone (flash) mode
2186SAMLight20.04.2016BugfixUSC-2 IPG type E adjustable pulse duration
2179SAMLight05.04.2016BugfixMarkEntityByName with EntityNamesSeparatedBySemicolon JobExecutionDelay ignored
2178SAMLight05.04.2016FeatureIPG laser special laser sequence (AdjustablePulseWidth) on flash
2176SAMLight05.04.2016BugfixRTC trigger mode, jitter on MarkingActive / JobExecutionDelay
2172SAM29.03.2016BugfixMany SAM settings, like all ScPropertyPage settings, could not be saved permanently.
2151SAM14.03.2016BugfixThere are Event leaks - two per saving - if saving settings or job with e.g. Samlight.
2154SAMLight09.03.2016BugfixSAMLight settings are not saved on exit
2123SAMLight09.03.2016BugfixPen settings - different SkyWriting delay rules
2146SAMLight09.03.2016BugfixRamping on very short lines with high speeds causes slower scanner speeds
2112SAMLight09.03.2016Bugfixthe control page flickers
2098SAMLight09.03.2016BugfixLens Correction File (*.lcf) with "=" sign does not work
2159SAMLight04.03.2016FeatureImplement Client Control constats for Pens -> SPI-G3 -> Waveform, Simmer Current and CW
2155SAM25.02.2016BugfixLoading or saving SAM job files on the network could produce not signalled error - e.g. not saved.
2136SAM28.01.2016BugfixCreating new ScWinTextChars2D at the working area could show initially undesired char.
2128SAMLight25.01.2016BugfixScWaitForInput control objects are ignored
2133SAMLight22.01.2016BugfixMarkTrigger does works erroneus, when pre- / post job is blue motion ctrl
2131SAMLight22.01.2016BugfixClientCtrl cmd 'ScGetEntityOutline()' did not work, if requested item(s) were grouped before.
2124SAMLight18.01.2016BugfixIn SAMLight Settings -> System I/O "JobSelect" and "JobSelect USC-2 Ext" are not stable.
2122SAMLight14.01.2016BugfixImport flags handling wrong

Version 3.5 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
2231SAMLight05.05.2017BugfixTiming issues can cause usc2 card settings to flip
2139USC-2 Firmware08.06.2016BugfixSporadically slow movement of USC-2 after booting
2133SAMLight22.01.2016BugfixMarkTrigger does works erroneus, when pre- / post job is blue motion ctrl object
2131SAMLight22.01.2016BugfixClientCtrl cmd 'ScGetEntityOutline()' did not work, if requested item(s) were grouped before.

Version 3.4.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
2061SAMLight29.05.2020BugfixSAMLight User Level User without any privileges can edit entities in Special Sequences / Jobs Toolbar
823SAMLight18.05.2020FeatureStart SAMLight with default settings
1958SAMLight13.05.2020BugfixOptic3D - 3D Point Clouds are displayed correctly
2054SAMLight13.05.2020BugfixSometimes USC-1 home jump is not executed after red pointer stop
2108SAMLight13.05.2020BugfixLCF file ZCorrEnabled is ignored
1968USC-2 Firmware13.05.2020FeatureApply new correction file in standalone mode
2064SAMLight27.01.2017BugfixSAMLight Client Control command LastExpectedMarkTime resets OptoOuts to default value
1983SAMLight28.09.2016FeatureOptic3D - 3D Surfaces - STL Z-Projection
2068SAMLight09.03.2016FeatureGrayscale bitmap marking - direct control of all 256 grayscale values
2089SAMLight09.03.2016BugfixWrong stepper signal (type 14) in bitmap rotary line by line mode (OPTO_OUT signals)
2088SAMLight09.03.2016BugfixHoming position is not updated in Control window
2076SAMLight09.03.2016FeatureCheckbox for parameter"MarktriggerUpdateBeforeEnd"
2087SAMLight09.03.2016Bugfixrelative problem of splitting delay
2085SAMLight09.03.2016BugfixThe center of QR-Code-Ex is not fixed while using the keep-size feature
2121SAMLight11.01.2016Featureclient control command for Settings ->Optic->rotation
2116SAMLight08.01.2016Bugfixpostprocessing does not work in splitting mode
1933SAMLight21.12.2015BugfixKorean or arabic characters cannot be set radial or as single characters
2106SAM07.12.2015BugfixIn case radial text, if only ONE char AND 'radial middle' combo item is selected, char is NOT centered.
2081SAMLight01.12.2015BugfixHoming problem after red pointer by using 1D Planar Splitting
2104SAM01.12.2015BugfixEven DirectWrite not active, loading of the corresponding Dll's by SAM could result in Samlight hangup forever.
2100SAMLight26.11.2015BugfixRTC5, 2D splitting, mark dialog ext.stop is not detected
2099SAM24.11.2015BugfixImport of bmp could result in empty Entities2D
2097SAMLight19.11.2015BugfixRTC5 changes of laser and scanner delays are applied too early
2066SAMLight27.10.2015FeatureChange Laser Names in the Caption of the Pen windows and Marking Property Page
2084SAMLight26.10.2015BugfixSelect multiple ScWinTextChars2D and edit the text simultaneously
2071SAMLight26.10.2015FeaturePersian calendar support
2083SAMLight19.10.2015BugfixStepper 14 loses move on overflow
2041SAMLight10.10.2015FeatureNew Flag "reverse Movement Direction"
2058SAMLight10.10.2015Bugfixsome functions of step and repeat do not work
2073SAMLight10.10.2015FeatureCreate Report file which logs the user's marking activities
2070SAMLight01.10.2015FeatureOptic3D - 3D Surfaces - STL Z-Projection - CCI commands
2075SAMLight01.10.2015FeatureRedpointer Ctrl-ArrowKey--Nudge
2077SAMLight01.10.2015BugfixJob process not parallel after some MultiHead ControlObjects
2063SAMLight17.09.2015Featurea constant for the advanced feature "use pen colors" is required now for CCI
2065SAMLight15.09.2015Bugfixuse of red pointer with repeated execution of CCI command LastExpectedMarkTime adds up mark times
2056SAMLight24.08.2015BugfixDue to a erroneous Samlight-Home-Jump implementation, home jump could be set or interpreted false.
2017SAMLight24.08.2015BugfixUSC-1 home jump is not executed after red pointer stop
2048SAMLight24.08.2015FeatureDecimal numbers substitution
2053SAMLight24.08.2015BugfixMultiCard - display of working areas not correct
2051SAMLight24.08.2015BugfixZ-Dimension translation and scale of point clouds does not work
2045SAMLight12.08.2015FeatureUpdated import filter for import of dxf, cmx, svg, etc.
2035SAMLight10.08.2015FeatureControl through ClientCtrl the option "enable PenPaths" and the option "center objects" e.g. after svg import
2044SAMLight10.08.2015BugfixFor 'entity based splitting', different hatches for e.g. one char 'a' can have different center points.
2019SAMLight06.08.2015FeatureNew CCI import flags CreateOneGroup and CenterToField
2040SAMLight03.08.2015FeatureNew feature Show last recent jobs in SAMLight
2029SAMLight31.07.2015FeatureSAMLight implementation of Jobs Toolbar Entities in connection Mark Trigger
2032SAMLight31.07.2015Bugfixit was possible to open SAMLight Mark dialog and the Motion jog dialog parallel, what is not allowed
2034SAMLight31.07.2015BugfixRed pointer (Individual border) of ScPolyLine2D does not work
1306SAM31.07.2015FeatureFor all motion with homing caps, a nonmodal dialog should show running homing and a cancel button should be available.
1992SAMLight27.07.2015BugfixWhen often saving current job to file during same session through e.g. ClientCtrl, memory usage increases.
2006SAMLight21.07.2015FeatureDisable STOP button for homing on startup of SAMLight by command line parameter
2024SAMLight17.07.2015FeatureAdd the optic rotation paramter to the Lens Correction File (*.lcf).
2026SAMLight13.07.2015BugfixUSC-2, flash mode, IPG laser modes are limited to a frequency range
2011SAMLight07.07.2015BugfixUSC-2 unpause bypasses WaitForInputControlObject and WaitForTrigger
2021SAMLight06.07.2015BugfixSamlightClientCtrl under x64 does not do TCP connect successfully.
2015SAMLight06.07.2015BugfixOutput bit while moving cannot be set via Stepper Motor Type 8 Motion GUI
1976SAMLight17.06.2015FeatureImport Filter now wih new improved version for Import of dxf, cmx, svg etc...
1938SAMLight09.06.2015FeatureCCI - Faster access to "Lens Switcher"
2004SAMLight03.06.2015BugfixRotated BW bitmap wrong direction of bi-dir. shift and skywriting
1843SAMLight01.06.2015BugfixIf command line parameter is added to Startmenu link file in Make Installer Settings dialog the icon won't appear in Startmenu
1999SAMLight01.06.2015BugfixSAMLight does not start with missing motion controller type 5 (MDrive)
1896SAMLight28.05.2015FeatureOptic3D - Z-Array - create reference copies of the selected entity in Z dimension.
1998SAM26.05.2015BugfixIf kernel property ScDebug() is set to scComDebugNoOutput, there could occur problems before.
1995SAMLight21.05.2015FeatureBmp cutting now should work without overlap or gaps between the single cuts.
1980SAMLight13.05.2015FeatureImplement JOB_SELECT_AUTO_RUN flash JobIOSelect mode (mark job # 1 without trigger)
1969SAMLight13.05.2015FeatureRead XY2-100 status in SAMLight for USC-2 cards
1961SAMLight13.05.2015FeatureCCI - check if used font is available
1986SAMLight13.05.2015BugfixWhen a job has a Pre, Post-Processing and Main Job, only the Pre-processing job will be marked by CI call
1978SAMLight13.05.2015BugfixWhen in JobIOSelect mode. Using a client control application to load job in flash fails.
1988SAMLight13.05.2015FeatureImplement User Right to Edit an Entity but being restricted to change the position or size of the entity.
1989SAMLight11.05.2015BugfixBitmap import was limited to 100 million pixel
1985SAMLight08.05.2015BugfixIn Step & Repeat "Keep Marking Active Output" will not stay High until end of process
1981SAMLight23.04.2015FeatureCCI - set motion control string
1972SAMLight16.04.2015BugfixValue for Num Loops is missing in SAM3D Style export
1965SAMLight14.04.2015Featurechange text size for several text entities without changing test of entities
1959SAMLight07.04.2015BugfixOptic3D - DeepEngraving - negative step values
1960SAMLight01.04.2015FeatureClockwise wobble direction for RTC5
1964SAMLight25.03.2015BugfixMarking problem with MultiHead and 2 RTC3 cards
1913SAMLight24.03.2015FeatureMOTF Bitmap Feature - only USC-2 card
1962SAM20.03.2015BugfixDoing 'real' array copy ( by dialog in working area ) can crash when undo that.
1935SAMLight16.03.2015BugfixPaste problem in Text2D property sheet
1957Installer11.03.2015FeatureNew Setup contains new USB driver for USC cards for better USB 3.x compatibility.
1918SAMLight09.03.2015BugfixError when Redpointer Individual Border is selected and using wavelength factor so that RP exceeds field size
1915SAMLight09.03.2015Featurenew View2D mode Show only selected (entity/-ies) in View2D
1949SAMLight18.02.2015BugfixIf home jump is disabled in Samlight, internal Sam library default value still was on 'enabled' in case RTC card.
1947SAMLight18.02.2015BugfixRedpointer sometimes reported 'out of working area' error, even this should have been adjusted.
1943SAMLight13.02.2015BugfixBug in entity based splitting, typically if pen path is used.
1937SAMLight06.02.2015Feature3D-Point Cloud Data Import
1940SAM06.02.2015BugfixStepper motion type 8 for RTC cards contained an error.
1931SAMLight26.01.2015BugfixUSC-2, Trigger Mode - "Current" time doesn't show the mark time in real time

Version 3.4 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1992SAMLight17.07.2015BugfixWhen often saving current job to file during same session through e.g. ClientCtrl, memory usage increases.
2021SAMLight06.07.2015BugfixSamlightClientCtrl under x64 does not do TCP connect successfully.
2015SAMLight30.06.2015BugfixOutput bit while moving cannot be set via Stepper Motor Type 8 Motion GUI
1964SAMLight14.04.2015BugfixMarking problem with MultiHead and 2 RTC3 cards
1962SAM20.03.2015BugfixDoing 'real' array copy ( by dialog in working area ) can crash when undo that.
1949SAMLight18.02.2015BugfixIf home jump is disabled in Samlight, internal Sam library default value still was on 'enabled' in case RTC card.
1947SAMLight18.02.2015BugfixRedpointer sometimes reported 'out of working area' error, even this should have been adjusted.
1940SAM06.02.2015BugfixStepper motion type 8 for RTC cards contained an error.

Version 3.3.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1932SAMLight13.05.2020BugfixAngular splitting with redpointer always moves back to start position
1863SAMLight13.05.2020FeatureDefocus for USC-2 + Flatlens (without Optic3D)
1903SAMLight14.09.2016BugfixHatch line congruent with contour
1930SAMLight19.12.2014BugfixLaser Gate keeps active between groups with NumLoopCounts in flash mode
1926SAMLight12.12.2014FeatureEntity based splitting for MOTF now allows higher resulting marking speeds
1916SAMLight11.12.2014BugfixMark Start dialog can't be closed if RTC3 is stopped with an entity with high Mark Loop Count via Trigger Stop
1922SAMLight10.12.2014BugfixStepper Motor Type 8 does not move to start position after first mark for Angular Bitmap Marking
1787SAM10.12.2014FeatureEntityInfo flag Output As Bitmap
1925SAMLight08.12.2014BugfixDrill Geometry does not work in MultiHead mode
1908SAMLight04.12.2014FeatureSwitch MIP Signal of USC cards off during execution of control objects
1923SAMLight03.12.2014BugfixWhen using Multihead with 2 cards then a dotted QR Code in the filed of the second head is not marked
1909SAMLight03.12.2014FeatureCheckbox in import dialog for DataWizard Create One Group
1920SAMLight01.12.2014BugfixMOTF Splitting - USC-1 Buffering
1917SAMLight27.11.2014BugfixEntity based splitting produces potentially failure markings with ScSerialNumber2D/ScWinTextChars2D.
1894SAMLight17.11.2014FeatureVisual Axis Position Shift
1895SAMLight13.11.2014BugfixOptic3D - Deep Engraving reworked
1907SAMLight13.11.2014BugfixTwo ethernet connections are detected as one card connected via USB and Ethernet
1793SAMLight07.11.2014FeatureBitmap Rotary with Type=14
1906SAMLight07.11.2014BugfixClient Control - Entity specific calls of ScMarkEntityByName marks whole job
1897SAMLight31.10.2014FeatureKeep background flag when reimporting bitmap, only create scanner bitmap if activated
1901SAMLight26.10.2014BugfixRedpointer wavelength factor and offset was not working anymore.
1900SAMLight26.10.2014FeatureMOTF Splitting reworked
1890SAMLight20.10.2014BugfixLaser Gate stops shortly between NumLoopCounts in flash mode
1888SAMLight20.10.2014BugfixShift in serialnumber characters in flash mode
1892SAMLight15.10.2014FeatureHatch-Styles with more than 2 pens
1869SAMLight10.10.2014FeatureOptic3D - 3D Surfaces - Cylinder
1886SAMLight07.10.2014BugfixIf switching from splitted redpointer to marking, wrong 're-split job ?' message could occur.
1884SAM02.10.2014BugfixScCut() Function of ScVectorTool in Tools did not always split correct in case 2D
1860SAMLight26.09.2014FeatureFor 1D Marking On The Fly Splitting, 'Entity based splitting' now is available.
1882SAMLight25.09.2014BugfixMark dialog freezes if auto pointer and repeat mark is activated
1867SAM24.09.2014FeatureFor motion type 8 ( stepper ), all settings can be editited and changed during a Samlight session.
1880SAMLight23.09.2014FeatureAll Samlight splitting functionality now is able to use any number of bitmaps for splitting ...
1875SAMLight02.09.2014Bugfixwrong SAMLight chm. help file loaded for German and French SAMLight language resource file
1872SAMLight29.08.2014BugfixLaser frequency with Override Frequency slightly below 100% drops below Min Frequency in Optic Settings
1873SAMLight29.08.2014BugfixRed-pointer mode 'selected' could not be disabled by CCI call
1864SAMLight27.08.2014Feature"Lens Init Job" to execute control objects when UCF correction file is loaded
1870SAMLight25.08.2014BugfixBarcode reader mode of a serial number cannot be enabled as default
1868SAMLight20.08.2014BugfixFor Step&Repeat, second move axis relative moves were inverted before.
1866SAM18.08.2014FeatureRead 2 inputs at the Laser Connector ( RTC 5 command get_laser_pin_in ) with Client Control
1861SAMLight11.08.2014FeatureIndividual SystemPixelMaps for MultiHead
1862SAMLight07.08.2014FeatureInclude checkbox to disable CO2 Laser Power 2 when not needed
1852SAMLight07.07.2014FeatureEnable single split red pointer parts being selectable by e.g. cursor key.
1856SAMLight07.07.2014BugfixIn BmpRotary, if 'Keep bitmap size' checkbox is set to off, the bitmap should be marked with new desired width or angle.
1831SAM03.07.2014FeatureBitmap Grayscale PWM with USC2 increase resolution
1853SAMLight03.07.2014BugfixSAMLight Client Control Reimport of Bitmap values of "Mark Loop Count" and "Blank Threshold" get lost
1849SAMLight18.06.2014BugfixWhen using multicard, pen names can be overwritten by head 0 names
1848SAMLight12.06.2014BugfixWhen using multicard and defining different laser types in sc_setup, laser type gets lost
1838SAMLight02.06.2014FeatureAdd a Client Control Call to CorrectCorrFile with sc_calib_points.txt
1574SAMLight28.05.2014FeatureDon't update View2D for 2D Planar Splitting
1790SAMLight28.05.2014BugfixPoints could be marked twice with Splitting
1840SAMLight28.05.2014FeatureAdd Split-preprocessing and Split-postprocessing for step&repeat and split modes in SAMLight
1837SAMLight20.05.2014BugfixIf shutting down windows, without closing Samlight before, some settings like short cuts could be lost.
1836SAMLight20.05.2014BugfixText2D string will be duplicated if you enable CharOutline in Text2D extended dialog
1832SAM07.05.2014BugfixDisplay of text in the SAM library 'Complex' codes like arabic are now displayed correctly.
1826SAMLight24.04.2014Bugfixall entities are shown by red pointer when using Mark Beat Count/Offset for only marking one entitiy one after another
1823SAM16.04.2014BugfixError in case penPath active.
1820SAMLight10.04.2014FeatureNew Data Wizard Set Order Flag 'Sort Equal Coordinates By Other Coordinate'
1816SAM02.04.2014BugfixRTC5. sometimes adjusting wrong frequency if auto_laser_control is on
1786SAM31.03.2014FeatureBitmap Extended Mark Feature LineIndexStep
1811SAMLight27.03.2014FeatureMotion home via short key and input (OPTO_IN)
1808SAM03.03.2014BugfixBmpRotary mode does NOT center line to mark in working area, if center is not equal to 0, 0
1805SAMLight03.03.2014Featureadditional Month and Time mappings
1798SAMLight21.02.2014BugfixIn Trigger marking mode, pressing 'extern stop' input lead to error message
1797SAM21.02.2014FeatureSamlight BmpRotary now supports pen path
1789SAM07.02.2014BugfixPen Drill Mode Number pulses are not correctly updated in some cases
1782SAM06.02.2014BugfixPen path with activated splitting now works for all cases.
1781SAM06.02.2014FeatureSamlight splitting improved, ScVectorToolScCut function improved.
1761SAM29.01.2014FeatureMarking point clouds with power defineable all over marking area Pen Intensity Bitmap
1778SAMLight28.01.2014FeatureSAM3D import of numbered 2d import files of a folder to generate a LayerSolid object
1783SAMLight27.01.2014BugfixMark Loop Count of ScJobRoot can be changed in combination with SAMLight Client Control
1747SAMLight24.01.2014FeatureUSC-2 - Additionally Z jump delay
1775SAMLight22.01.2014FeatureMax value for red pointer speed
1779SAM17.01.2014BugfixBMP Rotary does no motion increment, if bitmap line has no pixels to mark.
727SAM16.01.2014BugfixImport bitmaps color problems

Version 3.3 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1898SAMLight22.10.2014BugfixShift in serialnumber characters in flash mode
1886SAMLight07.10.2014BugfixIf switching from splitted redpointer to marking, wrong 're-split job ?' message could occur.
1884SAM02.10.2014BugfixScCut() Function of ScVectorTool in Tools did not always split correct in case 2D
1823SAM16.04.2014Bugfix Error in case penPath active.
1808SAM03.03.2014Bugfix BmpRotary mode does NOT center line to mark in working area, if center is not equal to 0, 0
1779SAM17.01.2014Bugfix BMP Rotary does no motion increment, if bitmap line has no pixels to mark.

Version 3.2.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1742SAMLight20.12.2016FeatureIn Flash Mode no Laser Gate signal when using Drill mode for points
1721SAMLight01.03.2016FeatureSTOP sequence in Jobs Toolbar
1770SAM16.12.2013FeatureUsing SAM function 'ScSetPropertyVariant()' can lead to unexpected behaviour
1767SAMLight10.12.2013BugfixReverse slicing does not mark the correct layer
1765SAM05.12.2013BugfixCaluculation of 'Time info' in simulation mode was incorrect ( less than expected ), if using Ramping
1757SAMLight02.12.2013FeatureBitmap marking - threshold for 'JumpOverBlankPixel'
1763SAMLight28.11.2013Featureadditional user at User Level
1675SAMLight28.11.2013Feature"Entity based splitting" mode does not center the split parts
1749SAMLight21.11.2013BugfixText object looses Z-Transformation when renewed
1752SAM20.11.2013BugfixStandBy pulse is only activated after first marking in StandBy Enable mode for USC-2 card in CO2 laser mode
1710SAM18.11.2013FeatureSpeed up point cloud import
1751SAMLight15.11.2013BugfixIn angular splitting, option 'move forward to start position' did not work anymore.
1738SAMLight15.11.2013FeatureImplement Don't Update View option in SAMLight
1720SAMLight05.11.2013Feature2D splitting start at bottom
1746SAM30.10.2013Featurenew barcode type GS1-128 introduced
814SAMLight25.10.2013BugfixShort keys are delete when changing from SAMLight 2D to 3D to 2D
1743SAM24.10.2013Bugfixproblem of entity alignment in connection with a motion control entity
1723SAMLight22.10.2013FeatureSAM3D mark beat count
1733SAMLight22.10.2013FeatureSAMLight Client Control command to change serial number text by entity name
1741SAM17.10.2013BugfixUsing the Tool ScCut function ( as Samlight splitting does ) did not necessary cutting in case 'cog'.
1722SAMLight10.10.2013FeaturePen-Path Icon
1731Installer09.10.2013BugfixStart menu entries missing
1728SAMLight09.10.2013Bugfixif empty splits in 1D splitting occur, this could lead to missing split at the end and preview error.
1725SAMLight01.10.2013Featurehide Trigger functionality by checkbox
1726SAMLight01.10.2013Featuresave job file automatically on SAMLight exit
1719SAMLight01.10.2013Featureplain ASCII SAMLight Client Control command ScCciUpdateViewNow() introduced
1717SAM26.09.2013BugfixUsing the Tool ScCut function ( as Samlight splitting does ) can produce unexpected marking behaviour.
1699SAMLight23.09.2013BugfixSAM3D - /hidden - CI
1700SAMLight23.09.2013BugfixSAM3D - external trigger checkbox does not reflect actual state in some cases
1713SAM20.09.2013BugfixSplitted jobs under MarkTrigger were not executed correctly.
1712SAM20.09.2013BugfixCOM interface at some locations was no more compatible for customer SAM Applications.
1707SAMLight05.09.2013FeatureIf using Pre- Post- Mark jobs toolbar, main job was no more selected in some latest versions.
1701SAMLight29.08.2013BugfixIf using Pre- Post- Mark jobs toolbar, sometimes e.g. a splitted job ocurred in the Postjob.
1697Installer22.08.2013FeatureFor WindowsXP, older USB driver now is used, to have no installation problems
1682SAMLight05.08.2013BugfixCCI value scComSAMLightClientCtrlDoubleValueTypeSecondaryHeadGainY could not be set
1687SAMLight31.07.2013BugfixAngular splitting mode with Y-Axis as split axis did not execute correct motion moves.
1683SAM12.07.2013FeatureSAM library now shows error message, if settings file is corrupt.
1680SAM10.07.2013Featureimprovements for SAM3D toolbars
1676SAMLight05.07.2013FeatureLock SJF to Dongle
1097SAM04.07.2013Featurenew LayerSolid import format SLC
1672SAMLight04.07.2013Featurez-correction import/export function
1674SAMLight04.07.2013BugfixMoving split lines in 1D Planar splitting causing improper motion commands
1673SAMLight02.07.2013BugfixUnwanted lines in hatch
1670SAM27.06.2013BugfixMulihead laser power control is randomly different for card 1 and card 2
1660SAMLight25.06.2013FeatureAdd new flag "Flash Dialog" for User Level Rights
1669SAM25.06.2013BugfixMoving MDrive gets SC_MOTION_CONTROL_EXEC_STOP_MOVE commands when USC-1/2 is not connected
1666Installer20.06.2013BugfixAt computers with USB 3 ports, SCAPS USB dongle did cause different access problems randomly.
1656SAMLight17.06.2013BugfixDirty flag gone after marking in SplittingMode
1663SAMLight17.06.2013BugfixPossible Pen Path problem in case splitting
1664SAMLight12.06.2013Feature'Memory underrun', may happen e.g. during saving of large job files, can be prevented if running under Win64.
1653SAMLight06.06.2013BugfixSAMLight freezes with trigger stop in combination with Laser Power Save Mode
1662SAM05.06.2013FeatureExcel file input for serial numbers now enabled optional use of Unicode strings
1659SAMLight04.06.2013BugfixShutter Control error message when activated
1639SAMLight03.06.2013FeatureUSC cards With optic3D -> enable Defocus of Redpointer to compensate wavelength
1652SAMLight03.06.2013BugfixRounded rectangle contains multiple points with the same coordinates
1651SAM13.05.2013FeatureImporting any file Now even possible, if path and / or filename is coded in NON local codepage
1649SAMLight08.05.2013BugfixIn splitting mode MarkingOnTheFly 1D, character based splitting now result is always centered ( and more )
1648SAMLight07.05.2013FeatureUsing char based splitting in 1D planar mode or angular mode, resulting split should be centered
1644SAMLight03.05.2013Bugfixsaving kills split lines
1626SAMLight11.04.2013FeatureNo visible split lines in entity based split mode
1638SAMLight11.04.2013BugfixIf starting a splitted job - and after that - going into the Split preview - the job is not placed correctly
1636SAMLight03.04.2013BugfixWith RTC5 or RTC4 cards, Mark Trigger window can close at ext. trigger stop, even if this is not desired
1635SAM27.03.2013BugfixExtended settings of ScWinTextChars2D 'LineCenter' did not work for longer text objects
1630SAMLight21.03.2013FeatureEnable Z-Coordinate for Redpointer
1627SAMLight20.03.2013FeatureDownSizing of settings file with Samlight command line option now possible
1621SAMLight20.03.2013BugfixUSC-2 & 2head gain / offset / rotation for individual heads does not work
1504SAM22.02.2013BugfixPen is not set correctly in combination with Pen Path
1618SAMLight22.02.2013Bugfix'Entity based splitting' did NOT take the first element into account - first element was not conrained in the split
1615SAMLight20.02.2013BugfixFor some builds, splitting was not able anymore
1555USC-2 Firmware08.02.2013FeatureMotion control on USC2 hardware
1350SAM07.02.2013FeatureHatching 4 hatches per entity
1607SAMLight06.02.2013BugfixSwitch off Settings saving is not updated in settings file
1556SAM01.02.2013FeatureNew stepper mode for supporting USC2 onboard motion control
1602SAMLight30.01.2013BugfixClient Control command SC_SAMLIGHT_CLIENT_CTRL_DOUBLE_DATA_ID_HATCH_NUMLOOPS1 / 2 did not work
1605SAMLight30.01.2013FeatureImplement new Leadtools dll's
1362SAM29.01.2013Featurenew version of import library
1186SAM29.01.2013Bugfixgerber files with special content can't be imported
1604SAMLight16.01.2013Bugfix"set_continues_mode 1" error message for RTC cards in combination with CCI command ScStopMarking
1603SAMLight11.01.2013FeatureDisable EmissionEnable during WaitForInput if SwitchOffDuringJumps is enabled

Version 3.2 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1697Installer16.04.2020Feature For WindowsXP, older USB driver now is used, to have no installation problems
1675SAMLight28.11.2013Feature "Entity based splitting" mode does not center the split parts
814SAMLight25.10.2013Bugfix Short keys are delete when changing from SAMLight 2D to 3D to 2D
1731Installer09.10.2013Bugfix Start menu entries missing
1728SAMLight09.10.2013Bugfix if empty splits in 1D splitting occur, this could lead to missing split at the end and preview error.
1717SAM26.09.2013Bugfix Using the Tool ScCut function ( as Samlight splitting does ) can produce unexpected marking behaviour.
1713SAM20.09.2013Bugfix Splitted jobs under MarkTrigger were not executed correctly.
1707SAMLight05.09.2013Feature If using Pre- Post- Mark jobs toolbar, main job was no more selected in some latest versions.
1701SAMLight28.08.2013Bugfix If using Pre- Post- Mark jobs toolbar, sometimes e.g. a splitted job ocurred in the Postjob.
1687SAMLight31.07.2013Bugfix Angular splitting mode with Y-Axis as split axis did not execute correct motion moves.
1683SAM12.07.2013Feature SAM library now shows error message, if settings file is corrupt.
1676SAMLight05.07.2013Feature Lock SJF to Dongle
1672SAMLight04.07.2013Feature z-correction import/export function
1674SAMLight04.07.2013Bugfix Moving split lines in 1D Planar splitting causing improper motion commands
1659SAMLight04.06.2013Bugfix Shutter Control error message when activated
1649SAMLight08.05.2013Bugfix In splitting mode MarkingOnTheFly 1D, character based splitting now result is always centered ( and more ):
1644SAMLight03.05.2013Bugfix saving kills split lines
1626SAMLight11.04.2013Feature No visible split lines in entity based split mode
1638SAMLight11.04.2013Bugfix If starting a splitted job - and after that - going into the Split preview - the job is not placed correctly:
1636SAMLight03.04.2013Bugfix With RTC5 or RTC4 cards, Mark Trigger window can close at ext. trigger stop, even if this is not desired:
1630SAMLight21.03.2013Feature Enable Z-Coordinate for Redpointer
1627SAMLight20.03.2013Feature DownSizing of settings file with Samlight command line option now possible:
1555USC-2 Firmware08.02.2013Feature Motion control on USC2 hardware
1607SAMLight06.02.2013Bugfix Switch off Settings saving is not updated in settings file:

Version 3.1.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1561SAMLight10.09.2021Featureserial number should be auto reset while time shift map changes
1326SAMLight12.02.2013BugfixClientCtrl function 'IsMarking()' does not work correct in case MarkTrigger.
1596SAMLight19.12.2012Feature'Selected' checkbox at Mark Start dialog should be deactivated or hidden for splitted job files
1600SAM12.12.2012BugfixTiming dependant, USC-2 can slow down with large delays ( up to 100 s ), mostly in TCP mode, seldom with USB
1599SAM12.12.2012FeatureIf loading *.s3d file under SAM3D in Samlight, it's path and name is not shown in the windows title bar
1495SAMLight06.12.2012Feature"Vector Marking - Entity Based Splitting" for Ring Splitting
1597SAMLight03.12.2012FeatureAllow configuration of default load/save flags
1595SAM19.11.2012Featurepoint cloud import from HPGL with many pen changes
1590SAMLight30.10.2012FeatureImprove char based splitting.
1591SAMLight24.10.2012FeatureEnable Pen saving in 3D
1589SAMLight24.10.2012Bugfix"Slice From File" might create unhatchable layers
1588SAMLight24.10.2012FeatureAllow CO2 Power Map values to be entered in watt
1263SAM22.10.2012BugfixArray functionality of the EntityInfo property page does not work with Ramping Settings for Pens
1586SAMLight19.10.2012BugfixWrong moves, if using Splitting in angular mode WITH 'character based splitting', especially WITH white space inside the text.
1584SAMLight19.10.2012BugfixIn case RTC card, when using ClientCtrl ScMarkEntityByName(), Trigger windows does not close.
1582SAMLight17.10.2012FeatureFor stepper motion type 08, accurate position gets lost, if motion is stopped before end.
1580SAM11.10.2012BugfixIn SAM3D, saving of slicing data in the s3d job file sometimes saves not all data.
1233SAM04.10.2012Bugfixserial numbers "Actual Value" is not updated within SerialNumber property page after marking
1577SAM25.09.2012BugfixPen Misc Hatch flags do not work correctly with Pen Path feature under special conditions
1200SAM14.09.2012FeatureRTC4 increase the laser frequency on 1 MHz
1571SAMLight14.09.2012BugfixIf NOT running USC-cards, do NOT show the MarkingOnTheFly Splitting dialog option.
1548SAMLight13.09.2012BugfixBug in Splitting 1D MarkOnTheFly
1568SAM11.09.2012BugfixUnder Sam3D, if doing slicing with slice distance smaller or equal to 10 um, some slices were created in a wrong way.
1566SAMLight06.09.2012BugfixUnder Sam3D, ExternStop or MarkDialog->Stop often did not work.
1534SAMLight06.09.2012FeatureIf using ClientCtrl, no more start of both Apps as Admin is required ( under Windows Vista / Windows 7 ).
1564SAM04.09.2012BugfixIn pen main dialog, if you change the pen through the combo box, some parameters in the drill page were NOT updated.
1560Tools03.09.2012Bugfixfont converter tool. Under certain conditions, after editing, a sign will not saved.
1562SAMLight03.09.2012BugfixIn case Angular Split Preview, split angle was taken as distance, what was wrong.
1506SAM03.09.2012BugfixBug in using 'serial number as barcode'
1558SAM14.08.2012BugfixDate Time entity format changed
1554SAM14.08.2012BugfixFor property page dimension and in center mode, it was not possible for objects with only one dimension to set center to 0.
1557SAM14.08.2012BugfixIPG Interface D1 not working with RTC5
1553SAM03.08.2012BugfixWith motion type 'stepper motion' ( type 8 ), 'fast homing' ( reference switch connected to ExternStop ) had problems.
1465SAM31.07.2012BugfixSAM3D redpoint shows the slice of a previous 3d loaded job file although a new 3d job is already loaded
1545SAMLight19.07.2012BugfixWhen using MarkTrigger, since 02.2012 MarkTrigger windows closes, if e.g. extern stop input is active.
1544SAM18.07.2012BugfixImport of Points/PointClouds via hpgl/plt doesn't work with import option "Import To Pen Groups"
1537SAM17.07.2012Bugfixadditional endpoint for a circle in combination with some segment count numbers
1542SAMLight17.07.2012BugfixWhen using angular splitting, step calculations were erroneous by ~ 0.1 degree.
1540SAM11.07.2012BugfixRTC cards If using MarkTrigger and closing the window by clicking the Stop button, window is re-opened again.
1539SAMLight10.07.2012Featurenew SAMLight Client Control constant scComSAMLightClientCtrlLongDataIdEntitySerialResetCount
1538SAMLight10.07.2012Featurenew SAMLight Client Control constant scComSAMLightClientCtrlLongDataIdEntitySerialBeatCount
1533USC-2 Firmware09.07.2012FeatureUSC-2 should display timer information
1532SAMLight04.07.2012FeatureSAMLight Client Control constant for getting the rotation angle of an entity
1519SAM04.07.2012Feature"Galvo Coordiantes ouf of range" error message should be displayed just once for a marking
1518SAMLight22.06.2012FeatureSAM3D entities should be centered in X and Y direction via GUI
1528SAMLight19.06.2012Bugfix1D Mark On Fly should be possible if no motion control is configured
1522SAMLight18.06.2012BugfixIf using splitting with mark trigger window, window closes after marking.
1524SAMLight18.06.2012BugfixAfter the break of the powering of the USC-1, the current correction file is not loaded. SAMLight is running!
1525SAMLight15.06.2012BugfixIn Sam3D, while marking a whole sliced object, current marked layer was not updated. And fixed crash during Startup.
1520SAM31.05.2012BugfixSCAPS detected ( and fixed ) two errors in ScGroup, which can cause unstable situations.
1515SAM18.05.2012BugfixError using COM call ScSetPropertyVariant with a string AND scComConfigStringIDAutoReleaseVariantString = true
1513USC-2 Firmware14.05.2012Bugfixcommand TXQ returns always "6 Entity not found"
1512USC-2 Firmware14.05.2012Bugfixswap MOTF channels A/B by software
1508SAM09.05.2012BugfixIf using a text object in case 'generate single charachters', it may loose it's 'blank'/'tab' or Ctrl chars.
960SAM04.05.2012Bugfixdxf object distorted
1503SAMLight26.04.2012Featurethe view of the offset value in the date time object is not updated.
1497SAMLight25.04.2012FeatureImplementation of a new option for the slicing mode. Close Distance.
1502USC-2 Firmware19.04.2012Bugfixinroduction of new commands JNI, ETC, ETB, FLAGS
1501USC-2 Firmware19.04.2012Bugfixinternal JobIOSelectMode
1500USC-2 Firmware19.04.2012Featureimplement reset and skip bits
1499USC-2 Firmware19.04.2012Bugfixpossibly a 18x18 DataMatrix can not contain 36 numerical charecters
1498USC-2 Firmware19.04.2012Bugfixcommand ST leads to corrupt SerialNumbers
1475SAM16.04.2012FeatureSpilt polyline should work for open polylines also
1449SAMLight12.04.2012BugfixThe language settings are not to save if the folder system of SAMLight is hidden
1490SAM10.04.2012FeatureUnder rare conditions, it may happen, that Minimize/Maximize Samlight main window crashes.
1470SAM04.04.2012BugfixCrash if typing in scanner values which are out of range
1484SAMLight03.04.2012BugfixDuring an external trigger stop, when home jump is executed, an optional power down command was executed too early.
1485SAMLight03.04.2012BugfixIf running sc_setup.exe AND configuring RTC4 / RTC5 MOTF settings, they are switched off after editing and saving.
1482SAMLight30.03.2012BugfixDue to bug fix 1473, 1D Planar AND Angular Splitting were starting their splits in wrong direction.
1481SAMLight30.03.2012FeaturePen drill properties are now available through Sam2D programming and for ClientCtrl interface.
1480SAM30.03.2012BugfixFor IMS motion, 'SpeedScale' was read from the settings file as integer ( but it is a float value ).
1471SAM26.03.2012BugfixUSC-2 standalonemode correction file with path including white spaces not working
1476SAM22.03.2012BugfixSelecting Barcodes "Ex Code39" or "Code 128 Subtype A" or "Code 128 Subtype B" crashes.
1473SAMLight22.03.2012BugfixSplitting with MarkingOnTheFly did not work completely correctly.
1472SAMLight19.03.2012Feature'non_splittable' object now works for StepRepeat.
1466SAM08.03.2012BugfixWith stepper motion driver, 'SignalAxisMovingState' may not signal as expected.
1460SAM16.02.2012BugfixIf Sam library host application is NOT Samlight, a timer message with id = 123 could be removed from the message pump
1454SAMLight15.02.2012Bugfix"load pens on file new" option resets OptOuts to default states
1451SAMLight14.02.2012BugfixBarcode DataMatrix & DataMatrixRect The invert option makes the shape of the datamatrix barcode rectangular.
1457SAM13.02.2012BugfixScBarCode12Chars2D - function ScCheckCharacters() had a memory problem
1345SAM13.02.2012BugfixGeometry Property Page doesn't show correct X/Y Radius for some job files
1456USC-2 Firmware13.02.2012FeatureOptimizedPolyDelay for Flash
1455USC-2 Firmware10.02.2012Bugfixerror flag "out of data"
1452SAMLight09.02.2012BugfixUsing stepper motion ( Type 08 ) and pressing many times the 'Go' button in the motion controls page could lead to problems.
1453SAM09.02.2012BugfixSam library function 'barcode->ScCheckCharacters( ... )' now works for QR-Barcode, too.
1450USC-2 Firmware31.01.2012Featureimplementation of remaining DateTime format placeholders
1447SAM31.01.2012FeatureNew Option 'scComSAMLightClientCtrlModeFlagMarkOrderAsSpecifiedWithNames' - powerful marking sequences can now be generated.
1448USC-2 Firmware26.01.2012Featureimplementation of DateTime format placeholders
1445SAM24.01.2012BugfixIPG Interface type D1 - wrong pulse length for last vector
1442SAMLight13.01.2012FeatureImprove settings for stepper motor -> sfactor
1412SAM12.01.2012FeatureDataWizzard improve close function
1439SAM09.01.2012BugfixUnder WINDOWS x64, light ctrl pen grid was not displayed correctly after application start.
1438SAM09.01.2012BugfixSpeed up Bitmap Split marking with stepper motion driver ( type 08 ).

Version 3.1 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1600SAM12.12.2012Bugfix Timing dependant, USC-2 can slow down with large delays ( up to 100 s ), mostly in TCP mode, seldom with USB:
1590SAMLight30.10.2012Feature Improve char based splitting.
1584SAMLight19.10.2012Bugfix In case RTC card, when using ClientCtrl ScMarkEntityByName(), Trigger windows does not close.
1580SAM11.10.2012Bugfix In SAM3D, saving of slicing data in the s3d job file sometimes saves not all data.
1571SAMLight14.09.2012Bugfix If NOT running USC-cards, do NOT show the MarkingOnTheFly Splitting dialog option.
1568SAM11.09.2012Bugfix Under Sam3D, if doing slicing with slice distance smaller or equal to 10 um, some slices were created in a wr
1566SAMLight06.09.2012Bugfix Under Sam3D, ExternStop or MarkDialog->Stop often did not work.
1564SAM04.09.2012Bugfix In pen main dialog, if you change the pen through the combo box, some parameters in the drill page were NOT u
1562SAMLight03.09.2012Bugfix In case Angular Split Preview, split angle was taken as distance, what was wrong.
1548SAMLight30.07.2012Bugfix Bug in Splitting 1D MarkOnTheFly
1545SAMLight19.07.2012Bugfix When using MarkTrigger, since 02.2012 MarkTrigger windows closes, if e.g. extern stop input is active.
1542SAMLight17.07.2012Bugfix When using angular splitting, step calculations were erroneous by ~ 0.1 degree.
1540SAM11.07.2012Bugfix RTC cards: If using MarkTrigger and closing the window by clicking the Stop button, window is re-opened again
1534SAMLight06.07.2012Feature If using ClientCtrl, no more start of both Apps as Admin is required ( under Windows Vista / Windows 7 ).
1528SAMLight19.06.2012Bugfix 1D Mark On Fly should be possible if no motion control is configured
1525SAMLight15.06.2012Bugfix In Sam3D, while marking a whole sliced object, current marked layer was not updated. And fixed crash during S
1522SAMLight31.05.2012Bugfix If using splitting with mark trigger window, window closes after marking.
1520SAM29.05.2012Bugfix SCAPS detected ( and fixed ) two errors in ScGroup, which can cause unstable situations.
1515SAM18.05.2012Bugfix Error using COM call ScSetPropertyVariant with a string AND scComConfigStringIDAutoReleaseVariantString = tru
1490SAM10.04.2012Feature Under rare conditions, it may happen, that Minimize/Maximize Samlight main window crashes.
1470SAM04.04.2012Bugfix Crash if typing in scanner values which are out of range
1484SAMLight03.04.2012Bugfix During an external trigger stop, when home jump is executed, an optional power down command was executed too
1485SAMLight03.04.2012Bugfix If running sc_setup.exe AND configuring RTC4 / RTC5 MOTF settings, they are switched off after editing and sa
1482SAMLight30.03.2012Bugfix Due to bug fix 1473, 1D Planar AND Angular Splitting were starting their splits in wrong direction.
1476SAM22.03.2012Bugfix Selecting Barcodes "Ex Code39" or "Code 128 Subtype A" or "Code 128 Subtype B" crashes.
1473SAMLight22.03.2012Bugfix Splitting with MarkingOnTheFly did not work completely correctly.
1460SAM16.02.2012Bugfix If Sam library host application is NOT Samlight, a timer message with id = 123 could be removed from the mess
1451SAMLight14.02.2012Bugfix Barcode DataMatrix & DataMatrixRect: The invert option makes the shape of the datamatrix barcode rectangular.
1457SAM13.02.2012Bugfix ScBarCode12Chars2D - function ScCheckCharacters() had a memory problem:
1445SAM24.01.2012Bugfix IPG Interface type D1 - wrong pulse length for last vector
1442SAMLight13.01.2012Feature Improve settings for stepper motor -> sfactor
1439SAM09.01.2012Bugfix Under WINDOWS x64, light ctrl pen grid was not displayed correctly after application start.
1438SAM09.01.2012Bugfix Speed up Bitmap Split marking with stepper motion driver ( type 08 ).

Version 3.0.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1178SAM08.03.2023BugfixDxf import inch parameter is not evaluated
1209SAMLight15.03.2021BugfixSAMLight Client Control Ramping settings are not saved within Pens
1288SAMLight16.02.2018FeatureActivate Startup Job and Mark Preprocessing (Jobs Toolbar) with Mark Trigger Mode
1253SAM12.12.2013BugfixEAN-13 Barcode can change pattern
1062SAMLight20.03.2012Featurenew client control constants for getting Pen Defocus parameter
1432USC-2 Firmware22.12.2011FeatureText properties "Reverse" flag
1434USC-2 Firmware22.12.2011Featureallow always FM 0
1433USC-2 Firmware22.12.2011FeatureStatus bits
1435USC-2 Firmware22.12.2011Bugfixreset External Trigger
1436USC-2 Firmware22.12.2011BugfixText properties "Reverse" flag is restricted on ordinary sn
1427SAM22.12.2011BugfixWobble does not work
1373SAM22.12.2011Featurepen paths
1420USC-2 Firmware16.12.2011BugfixSetOutput / WaitForInput doesn't work with bit 16 in a flash job
1415USC-2 Firmware16.12.2011Featuretext alignment on flash
1410USC-2 Firmware16.12.2011BugfixRS-232 baud rate becomes not active
1404USC-2 Firmware16.12.2011BugfixUSC-2 online help
1426USC-2 Firmware16.12.2011BugfixSerialNumbers may be incompatible between SN versions
1431SAM16.12.2011FeatureClientCtrl tcp commands are speeded up. Function interface commands ( no tcp ) are speeded up a bit, too.
1430SAM16.12.2011FeatureMaximum char count for a text2D string is increased from 1000 to 2048.
1428SAM14.12.2011Featurenew barcodes "Code 128 Subtype A" and "Code 128 Subtype B" introduced
1425SAMLight06.12.2011BugfixX and Y units strings at Min/Max ... dialog are set wrong for inch and bit
1424SAMLight06.12.2011BugfixSAMLight Client Control command ScChangeTextByName doesn't work corretly
1423SAMLight06.12.2011FeatureSet an entity as background entity via SAMLight Client Control
1422SAM02.12.2011FeatureNow it is possible to add a customer bitmap with variable alphaBlend as an overlay onto the working area.
1421SAM02.12.2011BugfixSAM call ScUpdate() or ScUpdateEx() needs too much time
1418SAMLight25.11.2011BugfixAngular Splitting with "Keep Marking Active Output“ activated OptoOut0 doesn't go low after marking
1405SAMLight25.11.2011Bugfixclient control scComSAMLightClientCtrlModeFlagEntityNamesSeparatedBySemicolon does not work in case ScMarkEntityByName
1299SAMLight25.11.2011FeatureEnable Move to Start Position for Angular Splitting
1413SAMLight24.11.2011BugfixLoadJob incl. Pens causing small memory leakage
1414SAM23.11.2011BugfixMemory leaks during loading job or Sam module settings.
1409SAM23.11.2011FeatureIPG laser mode for RTC3
1407SAM15.11.2011Featuredxf import style import circle as point
1408SAMLight15.11.2011BugfixClientControl Text content of DataMatrix Barcode is not set with 'scComSAMLightClientCtrlStringDataIdTextText'.
1403SAMLight14.11.2011BugfixMotor Motion Control should be deactivated while marking or redpointer
1401SAM11.11.2011FeatureSC_ILightExposureCtrl->ScEditPen( pen [ 0 .. 254 ] ) now returns S_FALSE, if PenDialog is cancelled.
1394SAM11.11.2011BugfixDataMatrixEx wrong outline in generate dots mode
1290SAMLight11.11.2011Bugfixdimensions of a rectangle in property page are not visible.
1289SAMLight11.11.2011Featurecontrol the motf delay with client ctrl for RTC cards
1269SAMLight11.11.2011Bugfix"Create Beam Comped Copy" leads to a skewed entity object.
1251SAMLight11.11.2011Featuregets system and user number of dongle
1214SAM11.11.2011BugfixCO2 Power Map changing values of %Laser1 and %Laser2 columns can only be applied by using comma
1399SAMLight11.11.2011FeatureSamlightClientControl can now run on customer machine without Sam installation !
1400SAMLight10.11.2011BugfixMultiHead job file just splitted for first Head
1398SAMLight10.11.2011FeatureMultiHead Job Execution Delay just executed for first Head
1397SAMLight09.11.2011BugfixStep&Repeat Planar 'Simulated axis' did not work anymore with deactivated motion.
1396SAMLight08.11.2011FeatureClientCtrl command for CreateBeamCompedCopy
1361SAMLight02.11.2011Bugfixrestart trigger mode if increment serial number was called
1392SAMLight28.10.2011BugfixSplit Preview Dialog does NOT show all splits at correct positions, if 'WORK_PIECE_MOVEMENT' checkbox is active.
1210SAMLight27.10.2011BugfixText2D entity & sign is not displayed correctly
1382SAMLight27.10.2011BugfixMotion Jog Jog Stepwidth in Jog dialog is not adopted from the Extra settings dialog
1363SAMLight26.10.2011BugfixMinMax values dialog don't show FPK values if laser does not require FPK
1381SAM25.10.2011FeatureIn the object lists context menu, it is now possible to hide optionally some entries.
1380SAMLight25.10.2011FeatureClientCtrl access to Bitmap Flag "x_scan_dir"
1379SAMLight21.10.2011Bugfixpossible value of 100.000 in space alignment of the text properties (extended) is too much.
1378SAMLight21.10.2011Bugfixgui does not update after select/deselect "Generate Single Characters" in text properties (Extended...)
1359SAMLight20.10.2011BugfixA Samlight->Menu->File->New command WITH an selected or opened Object list lead to open visuals and an invalid object list.
1358SAM20.10.2011BugfixDateTime entity DateTime Format is not available when loading the job file on another computer
1375SAM18.10.2011Bugfixserial number advanced dialog base number is not saved for X-based numbering system
1368SAM12.10.2011BugfixRTC4 MultiHead bad markings if HyperThreading is enabled
1365SAMLight09.10.2011FeatureClientCtrl Set motion control values with new ScSetEntityStringData() flag 'scComSAMLightClientCtrlStringDataIdSetMotionCtrls'.
1356SAM30.09.2011BugfixFixed missing extension for motion from 5 to 7 axis - before, 'external motion' like stepper or mdrive do not work correct.
1357SAMLight30.09.2011BugfixFixed endless motion move error under special angular Rotary1D splitting conditions.
1301SAM28.09.2011FeatureSpeed up splitting of big point clouds and split overlap parameter for points
1352SAMLight28.09.2011BugfixI/O Emergency stop does not work.
1355SAM28.09.2011BugfixCommands 'ScKernelScSetDefaultPropertyVariant()' and 'ScDocStreamScWrite()' now allow use of Ansi string data in VARIANT.
1354SAM28.09.2011FeatureSCI Dll add 3 new functions
1344SAM16.09.2011Bugfixgrouped entities cannot be aligned
1348SAMLight14.09.2011BugfixOption Nonmarkable can't be reset to normal
1005SAM13.09.2011Bugfixdxf import bug ( version 1 )
1346SAM13.09.2011BugfixSAM library exposes SAM COM structures in a wrong packing format ( 8 Byte instead of 1 Byte )
1343SAMLight13.09.2011FeatureSpitting horizontally aligned text with X axis as splitting axis
1341SAMLight19.08.2011Featureflag to save a job after every marking
1342SAMLight19.08.2011FeatureIPG D1 interface support with RTC4
1340SAMLight28.07.2011BugfixIn Step&Repeat Planar, with start position x=0 and y=0, an uninitialized, so random variable value was used.
1337SAM28.07.2011Bugfix'Right context menu functionality' in object list sometimes did not work.
1338SAM14.07.2011BugfixUnder Windows7 x64, initially shown object list and pen page is not complete.
1336SAMLight01.07.2011Bugfixreal bitmap splitting does not work
1334SAM16.06.2011BugfixSome ScLayerSolid COM commands, e.g. ScTypeId() crash, if using Microsoft '_com_ptr_t' Smart Pointer.
1324SAM10.06.2011FeatureTruncated PDF 417 Barcode
1325SAM06.06.2011FeatureIPG Laser Switch off Emission Enable during Jumps
1320SAMLight09.05.2011BugfixSplitting Fit Selected does not work in Split Preview dialog at Show split(s)
1313SAM19.04.2011BugfixBitmap marking mirroring and offset under special conditions
1319SAMLight12.04.2011BugfixClientControl Problem with ScSetEntityLongData( xxx, scComSAMLightClientCtrlLongDataIdEntitySetPen ) / ScChangeTextByName()
1317SAMLight08.04.2011FeatureFlag scComSAMLightClientCtrlMarkFlagEntityNamesSeparatedBySemicolon is changed
1316SAMLight08.04.2011FeatureClientCtrl Command ScChangeTextByName() can now handle more than one item to change for a single call.
1312SAMLight07.04.2011BugfixClientCtrl Command ScOpticMatrixTranslate() does not reset offset under special conditions.
1315SAMLight07.04.2011BugfixIf Menu->Mark->MarkOnlySelected is checked, Menu->Mark->Trigger only marks one item / Trigger.
1303SAMLight07.04.2011BugfixIf Menu->Mark->MarkOnlySelected is checked, Menu->Mark->Trigger only marks one item / Trigger.
1314SAMLight31.03.2011FeatureIncreased Samlight GUI reaction time with opened mark dialog.
991SAMLight25.03.2011Bugfixcrash after using the scroll bar in the point view
1311SAM23.03.2011BugfixCO2 Laser problem for high laser frequencies
1302SAMLight23.03.2011FeatureIntegration of BarcodeReader
1277SAM18.03.2011BugfixSoftware crash when changing MarkLoopCount with activated Point-Edit-Mode
1287SAMLight16.03.2011FeatureStart SAMLight when doubleclicking on a sjf-file in the windows explorer
1310SAMLight16.03.2011BugfixCCI Constant scComSAMLightClientCtrlLongDataIdEntitySerialCurrValue doesn't work in TCP mode
1279SAM09.03.2011Featurepen drill mode mark geometry on point postion
1305SAM03.03.2011FeatureScExecCommand( scComView2DCtrlExecCommandArchiveSaveAs ) now can open to a predefined path.
1300SAMLight24.02.2011BugfixIf logged in as "User" the user can save a jobfile without permission.
1298SAM17.02.2011BugfixRTC ScanAlone Problems with MultiCore CPUs
1041SAM14.02.2011BugfixDXF Import no read of Text if KeepOrder is checked
1295SAMLight08.02.2011BugfixThe Pulse function of the ScSetOutput object is not working.
1293SAMLight02.02.2011FeatureFor a splitted object, it is now possible to view split part details before marking.
1291SAMLight31.01.2011BugfixSoftware crash when doing an array copy with a serial number and then doing Edit->Undo
1281SAM17.01.2011BugfixEAN 13 - invert is not working properly
1286SAM16.12.2010BugfixRTC cards with Lee Laser and Power Save Mode Laser power is not set correctly
1285SAMLight14.12.2010FeatureScanner/Laser Delays and Jump speed of Pens to be hidden by User Level
1254SAMLight14.12.2010BugfixUser Level Supervisor password can be set without permission
1270SAM14.12.2010Bugfixbar code Ex Code39 not all lower case letters are supported
1280SAM03.12.2010BugfixSerial Number with text file cannot be reset under specific conditions with Windows 7
1278SAM26.11.2010FeatureIf exceeding limits with stepper motion ( type 08 ) in e.g. case splitting, it now stops after some error messages.
1276SAM26.11.2010FeatureStepper motion type ( 08 ) can now move a specified axis always first, if more than one axis should be moved.
1273SAMLight24.11.2010FeatureRTC5 LaserOn in Advanced PropertyPage/Power Map does not work
1272SAMLight18.11.2010BugfixSaving of job files / common saving at the end of Samlight session could randomly produce an ‘Unhandled Exception’ / crash.
1271SAMLight18.11.2010BugfixIf an input bit is used as 'stop marking' under MarkDialog, activating this bit only works once.
1268SAMLight16.11.2010BugfixSplitting VERTICAL Text in Rotary1D mode with option 'character based splitting' activated did succeed.
1267SAMLight15.11.2010BugfixRotary1D in angle mode runs to starting position before marking first split, what is wrong.
1265SAMLight12.11.2010Featurenew CCI Double Data Id constant scComSAMLightClientCtrlDoubleDataIdMotfOffset
1091SAM10.11.2010FeatureRTC5 support 20 bit resolution
1262SAM03.11.2010BugfixHatching with deactivated checkbox "Origninal Values" sets unreasonable hatch parameters
1258SAM25.10.2010Featuresupport of very big point clouds
1260SAMLight19.10.2010BugfixSamlight crashes under german windows, if started in 3D mode.
1256SAM30.09.2010Featurenew SAM Optic constants for changing MOTF values
1235SAM13.09.2010Featurespeed up USC get_opto_inputs
1177SAMLight25.08.2010BugfixShort Key table not saved with "save settings now"
1249SAM16.08.2010BugfixUsing stepper motion under vista/windows7 causes sporadic marking failure.
1225SAM06.08.2010FeatureControl Objects for changing Speed/Power/Freq override values
1113SAM06.08.2010Featureimplement the auto calibration function in SAMLight
653SAM06.08.2010FeatureAuto-Length for Ramping
1247SAMLight05.08.2010FeatureInput polling in conjunction with special menus not initially enabled after SamLight startup.
1242SAM30.07.2010BugfixIn Sam2D version 2.9.0 Sam2D programmers were able to send an e.g. ScMarkObject() out of a worker thread.
1240SAM30.07.2010BugfixIn Splitting Mode WITH Overlap, Lines at the border of a current split are sometimes not marked.
1238SAM29.07.2010BugfixUnder Vista / Windows 7 Sam2D may block.
1237SAMLight26.07.2010BugfixSAMLight JobSelect Mode Override parameters and PowerMap->Bits are changing to 0 when loading new job
1205SAMLight26.07.2010BugfixGerman or other language.chm file is not opened with corresponding resource file if Help->Contents is pressed
1229SAM16.07.2010BugfixAccess CO2 PowerMap
1231SAM16.07.2010BugfixBitmap Marking check x_scan_dir leads to crash
1227SAMLight16.07.2010Bugfix"&" sign not displayed correctly for a Text2D entitiy
1228SAMLight15.07.2010FeatureSAMLightClientCtrl new constant scComSAMLightClientCtrlLongValueTypeLastAutoCompensateResult
1169SAM12.05.2010BugfixRTC5 SetAutoLaserControl not disabled
1213SAM30.04.2010Featureimport of dxf layers
1208SAM25.03.2010BugfixSpaces within Text2D entites are not inserted with option "Generate single characters"
1203SAMLight22.03.2010Bugfixtcp communication to samlight times out.
1202SAM22.03.2010BugfixDateTime property page Advanced... button is still active without DateTime entity selected
1197SAM12.02.2010Bugfixsecond correction file not possible to select in RTC mode
1198SAM12.02.2010Bugfixsecond correction file not possible to select in RTC mode
1193SAMLight08.02.2010Bugfixlaser control ocx not visible
1184SAM15.01.2010FeatureSpeed up splitting of huge point clouds
1174SAM11.12.2009BugfixStepper motor fast homing doesn't work
1164SAM02.12.2009Bugfixediting the text of several serial numbers by Text2D extended leads to software crash
1092SAM02.12.2009BugfixUSC1 first direct command not working
1168SAM02.12.2009FeatureRTC ScanAlone Laser Mode 4
1167SAM01.12.2009FeatureStepper motor disabling of homing during software start
1161SAMLight20.11.2009Featureadd "control" property page to SAM3D View
1159SAMLight19.11.2009Featurepossibility to control parameter "Horizontal Split" and "VerticalSplit"in Split Dialog with help of SAMLight ClientCtrl
1158SAM16.11.2009BugfixPowermap doesn't work for YAG laser
720SAMLight05.11.2009FeatureGerman user manual
756SAM05.11.2009FeatureUnicode support for serial numbers
770SAMLight05.11.2009BugfixSAM3D Mode File New does not clear the file name in the title
809SAM05.11.2009FeatureActual Value of serial number property page
1145SAM04.11.2009BugfixProperty Pages are not displayed correctly with Windows 7
1144SAM20.10.2009Featurenew barcode GS1 Datamatrix
1142SAM15.10.2009BugfixUSC1 settings invert for laserport disabled
1136SAMLight15.10.2009FeatureCommand to reimport a dxf file does not work
1141SAMLight15.10.2009FeatureMultiHead Trigger Mode Start heads independently
1140SAMLight14.10.2009FeatureSAMLightClientCtrl new constants for ScGetStringValue GetLastErrorMessageInput, GetLastInfoMessageInput
1138SAM12.10.2009BugfixAfter Store and Restore of Entity Matrices, the outline might be damaged
1126SAM05.10.2009BugfixDataWizzard remove redundant points / short lines not removing double points
1134SAMLight02.10.2009BugfixSAMLight crashes when saving a write protected job
1121SAM22.09.2009BugfixControl Entity ScSetOutput Combine checkbox doesn't work
1122SAMLight21.09.2009BugfixUnder Windows Vista ( Home Premium Edition ) it is NOT possible to edit or set User-Login settings.
1129SAM21.09.2009Featureserial number imported from a .txt file lead to software crash
671SAM07.09.2009FeatureShow pen color in the mark page
1119SAMLight21.08.2009BugfixUser login dialog does not work, if all users have passwords.
1117SAM20.08.2009Bugfixcrash after putting more as 99 characters in Text2D Entity
1115SAMLight12.08.2009FeatureFor Serialnumber from file, a special column with ( text ) number in field allows repetition of current row without increment.
1068SAMLight21.07.2009FeatureSplitting with Mark-Trigger hides Mark-Trigger-Output window under stepper drive.
1107SAM21.07.2009BugfixMotion Control Entity dist is not applied with "Apply" and get lost when changing to other property pages/entites
1108SAM21.07.2009FeatureDataWizzard Dialog Additional Point Sort function OptimizePointCloudsOneRow

Version 3.0 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1303SAMLight01.03.2011Bugfix If Menu->Mark->MarkOnlySelected is checked, Menu->Mark->Trigger only marks one item / Trigger.
1277SAM08.02.2011Bugfix Software crash when changing MarkLoopCount with activated Point-Edit-Mode
1177SAMLight25.08.2010Bugfix Short Key table not saved with "save settings now"
1249SAM16.08.2010Bugfix Using stepper motion under vista/windows7 causes sporadic marking failure.
1247SAMLight05.08.2010Feature Input polling in conjunction with special menus not initially enabled after SamLight startup.
1242SAM30.07.2010Bugfix In Sam2D version 2.9.0 Sam2D programmers were able to send an e.g. ScMarkObject() out of a worker thread.
1240SAM30.07.2010Bugfix In Splitting Mode WITH Overlap, Lines at the border of a current split are sometimes not marked.
1238SAM29.07.2010Bugfix Under Vista / Windows 7 Sam2D may block.
1205SAMLight26.07.2010Bugfix German or other language.chm file is not opened with corresponding resource file if Help->Contents is pressed
1227SAMLight16.07.2010Bugfix "&" sign not displayed correctly for a Text2D entitiy
1210SAMLight20.04.2010Bugfix Text2D entity: & sign is not displayed correctly
1203SAMLight22.03.2010Bugfix tcp communication to samlight times out.
1164SAM02.12.2009Bugfix editing the text of several serial numbers by Text2D extended leads to software crash
1092SAM02.12.2009Bugfix USC1: first direct command not working
720SAMLight05.11.2009Feature German user manual
756SAM05.11.2009Feature Unicode support for serial numbers
770SAMLight05.11.2009Bugfix SAM3D Mode: File New does not clear the file name in the title
1145SAM04.11.2009Bugfix Property Pages are not displayed correctly with Windows 7
1134SAMLight02.10.2009Bugfix SAMLight crashes when saving a write protected job
1122SAMLight21.09.2009Bugfix Under Windows Vista ( Home Premium Edition ) it is NOT possible to edit or set User-Login settings.
1129SAM21.09.2009Feature serial number imported from a .txt file lead to software crash
1119SAMLight21.08.2009Bugfix User login dialog does not work, if all users have passwords.
1117SAM20.08.2009Bugfix crash after putting more as 99 characters in Text2D Entity
1115SAMLight12.08.2009Feature For Serialnumber from file, a special column with ( text ) number in field allows repetition of current row w
1068SAMLight21.07.2009Feature Splitting with Mark-Trigger hides Mark-Trigger-Output window under stepper drive.
1107SAM21.07.2009Bugfix Motion Control Entity: dist is not applied with "Apply" and get lost when changing to other property pages/en

Version 2.9.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1065SAMLight17.06.2010FeatureTo improve marking speed, an additional flag should allow NO gui updates during marking if running under MarkTrigger.
1105SAM15.07.2009FeatureDataWizzard randomize point cloud
1101SAMLight13.07.2009Feature Change behaviour of status output bit WaitingForExternalStart
1100SAMLight10.07.2009FeatureSAMLightClienttCtrl new import flag for reading PointClouds
1098SAMLight07.07.2009BugfixLaser Shut Down Mode not working reliable for small TimeOut values
1090SAM07.07.2009Bugfixarabic font do work not properly in generate single character mode
1096SAM03.07.2009BugfixImport of Excel data for serial numbers fails or provides empty values.
1086SAM25.06.2009FeatureHPGL import support for CI circle command
1075SAMLight20.05.2009BugfixSetting of the pen settings with the client control does not work properly.
1056SAM20.05.2009FeatureRTC5 Enable auto laser control
1026SAM11.05.2009BugfixPulse flag not set for a ScSetOutput Object
1057SAMLight07.05.2009Bugfix"Save settings now" does not work
1050SAMLight07.05.2009BugfixLoading of splitted job does not fully override default splitting and step/repeat settings
1048SAMLight07.05.2009BugfixRedpointer can be started if only Control Objects are in the entity list
1025SAMLight24.04.2009FeatureToolbar item 'ScSetSecondaryHeadOffset' in PreProcessing-Job-Dialog is enabled, even if running under USC-X interface card.
772SAM22.04.2009FeatureSAM3D Translate button on the dimension property page
817SAM22.04.2009FeatureSAM3D Start/End Layer
921SAM22.04.2009BugfixSCI Correction file can't be choosen when DLL interface is used
1006SAM22.04.2009BugfixSpeed ramping at end up to higher values
830SAMLight17.04.2009FeatureClient Interface Allow to control motion
1055SAMLight15.04.2009FeatureChinese letters are not displayed correctly
1051SAMLight09.04.2009Bugfixthe text of a text entity which is included in a serial number as barcode is not displayed correctly when loaded
1035SAM16.03.2009FeatureSpeed up splitting of PointClouds
950SAM26.02.2009BugfixCCI Mark operation is not influenced by IO parameters
1014SAM26.02.2009BugfixCrash in FEB-1 JobIOSelect mode
1002SAM20.02.2009BugfixError when importing AI file result is an empty job
1021SAM16.02.2009BugfixProblem when loading of old job files containing text
712SAM16.02.2009FeatureSAM3D layer specific pen
963SAMLight16.02.2009FeatureExtend 3D slicing functionality
1020SAMLight11.02.2009BugfixMarkDialog check of external IO messages not working
1001SAM10.02.2009FeatureSerialNumbers save/load enable all serial numbers flag
1012SAM09.02.2009Bugfixempty barcode property page and deactivated barcode content when creating barcode
1004SAMLight06.02.2009FeatureSAMLight ClientControl constants for activating/deactivating Power and Speed Ramping missing
1009SAM05.02.2009BugfixImport of ai-files ( Adobe Illustrator ) fails, when they were exported by CorelDraw11/12 as ai-version 3x / 4X
889SAMLight04.02.2009Featuredxf 2000 import bug
976SAM03.02.2009BugfixCrash during Import of SVG
954SAMLight27.01.2009BugfixIO Settings dialog cannot be edited with Geman resource file
610SAMLight26.01.2009BugfixPowerSave mode not working if RedPointer is running
995SAM23.01.2009Bugfixtext size of entity changes by editing text
986SAMLight19.01.2009FeatureConfigurable shutter output signal level
841SAMLight19.01.2009FeatureStart SAMLight in JobEditor Mode
836SAMLight19.01.2009FeatureRedpointer object
875SAM19.01.2009FeatureClient Interface Reimport Vector Graphic
952SAMLight19.01.2009FeatureExtend splitting functionality to take care about bitmaps
791SAM19.01.2009FeatureIPG Laser type with adjustable max frequency
652SAMLight19.01.2009FeatureSplitting in x and y direction
977SAM15.01.2009FeatureAppend .sjf extension to file name
753SAM12.01.2009BugfixCMX Import Problem with text orientation
708SAMLight12.01.2009FeatureEnable Splitting / Step&Repeat / Bitmap marking
916SAM22.12.2008Bugfixdxf import bad resolution importings splines
969SAMLight10.12.2008FeatureNew modes for the SAMLightClientCtrl for reaching very high performance
967SAMLight04.12.2008BugfixShort keys can't be saved
961SAMLight27.11.2008FeatureClientCtrl new constants for searching toplevel entities only
957SAM25.11.2008FeaturePointCloud Array Marking results has wrong size
956SAMLight24.11.2008BugfixCO2 and RepeatMark Laser sometimes stays on after pressing STOP
824SAMLight17.11.2008Featuresave screen through the ClientCtrl
860SAM17.11.2008Featureoptimize point clouds
915SAMLight14.11.2008FeatureCCI functions for manipulating bitmap greyscale map
929SAMLight30.10.2008BugfixUnder some fonts ( e.g. Arial ), one character ( e.g. '=' in case Arial ) is not displayable
833SAM20.10.2008BugfixDXF2 import too low resolution on some circles
906SAM20.10.2008Featurejpg import read correct dimension
872SAM20.10.2008FeatureSwitch to Leadtools V15
754SAM20.10.2008BugfixUSC1 setting external STOP for a longer time causes an error
822SAM20.10.2008FeatureSliceScroll GoTo button
811SAM20.10.2008FeatureSAM3D Hatch angle
862SAMLight20.10.2008FeatureDisplay Message Input window only if there are messages to report
216SAMLight20.10.2008Featurecustomers can create trial keys for full version
802SAM20.10.2008Featuremark time not shown
904SAM17.10.2008FeatureDataWizzard Create pen groups
851SAMLight10.10.2008BugfixCrash with Teach Outline
901SAM22.09.2008BugfixNegLaserOnDelay error
832SAM20.03.2008FeatureRTC4 introduce var jump delay

Version 2.9 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
1004SAMLight06.02.2009Feature SAMLight ClientControl constants for activating/deactivating Power and Speed Ramping missing

Version 2.8.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
718SAM17.11.2008FeaturePixelDitheredMode integrate bidirectional mode
722SAM17.11.2008Featureenable skywriting for dithered bitmap marking
700SAMLight20.10.2008BugfixEntity List is empty after loading of a job, also in connexion with Motion Control - Control
739SAMLight20.10.2008BugfixJob Select Mode last job is marked instead of current one
787SAMLight20.10.2008FeatureSAMLightClientCtrl access to Barcode LineReduction
774SAM20.03.2008Featurenew hatch style flag separate group for beam compensated lines
729SAM20.03.2008Bugfixscanner settings lost with change of hardware settings in setup.exe
773SAM20.03.2008FeatureSAM access to USC-1 3D parameters
755SAM20.03.2008FeatureCOM interface for accessing Spiral parameters
724SAM16.08.2007FeatureBitmap Pixel Drill Mode enable SkyWriting

Version 2.7.5

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
667SAM17.11.2008Featurenew control object set analog output
660SAM17.11.2008BugfixRTC4 Hangup when pressing Trigger STOP
578SAMLight29.09.2007BugfixSystem unit in Spiral Property Page
696SAM24.07.2007FeatureIncrease MinDigits of SerialNumber
666SAM28.05.2007FeatureIPG Mode for Scanlab ScanAlone card
662SAMLight07.05.2007Feature3D Array
642SAM26.04.2007BugfixPower and speed ramping does not work for high speed values
621SAM11.04.2007FeatureImport points from an ASCII file
617SAM22.03.2007BugfixIO value out of range can not be corrected
605SAMLight16.03.2007FeatureDecimal Stand By Pulse

Version 2.6.5xx

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
527SAMLight29.09.2007FeatureDivide object toolbar
287SAM22.03.2007FeaturePixelMode Use pen frequency for the output
459SAM22.03.2007FeatureSAM3D. change min possible slice distance
456SAMLight22.03.2007FeatureRotary functions introduced
463SAMLight20.03.2007FeatureSAM3D Mode with RTC3/RTC4 Allow to define a z-offset
343SAMLight20.03.2007FeatureMessageInputs combine input bits
468SAMLight12.03.2007FeatureRedPointer bit3 for the RTC4
477SAM12.03.2007FeatureError in BitmapConvertToPolylines
494SAM12.03.2007FeatureRTC4 Step motor commands through SAM interface
521SAMLight12.03.2007BugfixAlign can destroy objects
481SAM12.03.2007FeatureDxf text import
282SAM19.12.2006BugfixEntity item list does not show points from ScPointClouds2D
485SAMLight19.12.2006FeatureSAMLight and sc_setup should not run at the same time
424SAMLight19.12.2006Featureswitch between lense configurations
339SAMLight19.12.2006Bugfixexport in 3D mode
307SAMLight19.12.2006FeatureCommand line parameter jobname
276SAMLight19.12.2006BugfixMarkOnlySelected flag
539SAMLight23.11.2006BugfixMarkDialog "repeat mark" not working if "auto pointer" is checked
396SAM17.11.2006FeatureFEB1 unf with sjf
448SAM23.08.2006BugfixBitmapPropertyForm wrong positions if loading an older ressource file
358SAMLight18.08.2006BugfixEditRessource button always visible
400SAMLight18.08.2006BugfixPower update for pen missing
439SAM18.08.2006FeatureControl objects introduce enable flag
355SAMLight18.08.2006FeatureClientInterface functions for changing ScTimer, ScSetOutput...
290SAM08.08.2006FeatureGeometrical object Spiral
284SAM08.08.2006FeatureBarcode TextYOffset
357SAM08.08.2006FeatureMotion Control YOG buttons
34SAM08.08.2006Featurelarge entity handles in the view
406SAM08.08.2006FeatureCardProgInterface Add license for simulation
317SAM03.08.2006BugfixCrash within beamcompensation
315SAM03.08.2006BugfixDefocus value truncated
328SAM03.08.2006Featureincrease object count limit
298SAMLight03.08.2006FeatureOption Optic3D add 3D Preview
286SAMLight03.08.2006FeatureSAM3D plus Optic3D
434SAMLight03.08.2006BugfixSAMLight/SAM3D mode STOP button pops up
428SAM02.08.2006BugfixRTC4 YAG with IPG mode can not be unselected again
370SAMLight28.07.2006FeatureSAM3D rotate hatches
408SAM26.07.2006Featuresc_setup dongle diagnostic shows dongle type
411SAM24.07.2006FeatureOptimized Barcode Hatching
232SAM24.07.2006FeatureCreation of a Serialnumber containing Date Time
409SAM21.07.2006BugfixExcel serial file not available with Chinese or other language versions
403SAM20.07.2006FeatureHC3 use MARK_IN_PROGRESS_OUTPUT
399SAMLight17.07.2006FeatureHC3 RedPointer, SwitchOffDuringMark
382SAMLight07.07.2006FeatureSAMLightClientInterface get precalculated marking time
369SAM23.06.2006FeatureDisplay MDrives Device names in SAM
346SAMLight23.06.2006FeatureMark Start Dialog external trigger with auto pointer
381SAM23.06.2006FeatureHC3 use REMOTE_EXECUTE for mark in progress
380SAM14.06.2006Bugfixaccumulating errors if using the outline button for translations only
309SAMLight15.05.2006FeatureClientInterface new functions
312SAMLight11.04.2006FeatureSAMLightClientCtrl get/set job execution delay
260SAMLight27.03.2006BugfixJob IO Select mode
281SAM21.03.2006FeatureHPGL point import
278SAM21.03.2006FeatureFaulhaber motion controller
289SAM20.03.2006FeatureRessource editor window disappear
273SAM10.03.2006FeatureHC3 IO2 support for controlling lamp current over analog value
264SAM10.03.2006BugfixDXF2 import points does not work
33SAMLight07.03.2006Featurepassword protection / user levels / user management
266SAMLight06.03.2006BugfixClientCtrl ScGetIDStringData not working
221SAM03.03.2006FeatureIPG Mode for RTC4
263SAMLight02.03.2006BugfixHC3 External Trigger not possible out of Mark Start window
262SAM02.03.2006BugfixSetting HomePos failed
247SAMLight22.02.2006FeatureHC3 IPG Mode, show laser error messages
256SAMLight22.02.2006FeatureIO Error Messages
175SAMLight21.02.2006FeatureTraditional Chinese language
245SAM17.02.2006BugfixHC3 in IPG mode only half of the power can be adjusted
238SAM09.02.2006FeatureSupport for stacked RSS Barcodes
237SAM06.02.2006FeatureHC3 introduce IPG - SSmode
230SAM01.02.2006Featurecombination serialnumber and date/time
235SAM26.01.2006BugfixChinese version PixelMap settings can not be changed
228SAM18.01.2006FeatureUSC1 external trigger works only once in MOF mode
225SAM16.01.2006Bugfixpoint array does not mark
222SAMLight12.01.2006Featurespeed up IO JobMode
226SAM12.01.2006Bugfixmemory leak when loading a job with styles
123SAM18.11.2005Featurepreselect YAG2 for Lee mode
114SAM18.11.2005Featuremotion control support for IMS MDrive
129SAMLight18.11.2005Featurequantity reached counter sets an IO
110SAM18.11.2005Featurezick zack text marking
164SAMLight18.11.2005Bugfixpart counter mode counts also control objects
149SAMLight18.11.2005Bugfixpart counter mode with beat count objects
160SAM09.11.2005BugfixUSC1 wrong speed when marking 3d lines

Version 2.6 (STABLE)

IDSubsystemImplementedFeature/BugfixSummary of resolved bug / implemented feature
490SAMLight12.03.2007BugfixShow Quantity reached also in trigger mode
514SAMLight12.03.2007BugfixMark->Trigger does not increment serialnumbers
270SAMLight18.08.2006FeatureDate Time Advanced
299SAM10.04.2006BugfixMemory leak within MCL import
209SAMLight16.12.2005FeatureSAMLightClientCtrl get_num_entities and get_entity_name
178SAM30.11.2005Bugfixno valid license for text2d message
171SAMLight22.11.2005BugfixUSC1 output 2 and 5 are grayed